while checking some disks, I see this error with smartctl - Read defect list: asked for grown list but didn't get it
is this an issue with scale/cobia, with my hba, or all of the disks I have gone through so far, or something else entirely?
sudo smartctl -a /dev/sdz
is this an issue with scale/cobia, with my hba, or all of the disks I have gone through so far, or something else entirely?
sudo smartctl -a /dev/sdz
Code:
smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.1.55-production+truenas] (local build)
Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Vendor: ST8000VN
Product: 0002-1Z8112 SM
Revision: 4321
Compliance: SPC-3
User Capacity: 8,001,563,222,016 bytes [8.00 TB]
Logical block size: 512 bytes
Physical block size: 4096 bytes
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Logical Unit id: 0x500605ba003e9950
Serial number: ZA12FDB8
Device type: disk
Transport protocol: SAS (SPL-4)
Local Time is: Wed Nov 1 20:39:22 2023 CDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
Temperature Warning: Enabled
=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK
Current Drive Temperature: 38 C
Drive Trip Temperature: 0 C
Accumulated power on time, hours:minutes 0:00
Manufactured in week 24 of year 2008
Specified cycle count over device lifetime: 65536
Accumulated start-stop cycles: 49
Read defect list: asked for grown list but didn't get it
Error counter log:
Errors Corrected by Total Correction Gigabytes Total
ECC rereads/ errors algorithm processed uncorrected
fast | delayed rewrites corrected invocations [10^9 bytes] errors
read: 0 0 0 0 0 0.000 0
write: 0 0 0 0 0 0.000 0
Non-medium error count: 0
SMART Self-test log
Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ]
Description number (hours)
# 1 Default Completed - 59578 - [- - -]
# 2 Default Completed - 59554 - [- - -]
# 3 Default Completed - 59530 - [- - -]
# 4 Default Completed - 59506 - [- - -]
# 5 Default Completed - 59482 - [- - -]
# 6 Default Completed - 59458 - [- - -]
# 7 Default Completed - 59434 - [- - -]
# 8 Default Completed - 59410 - [- - -]
# 9 Default Completed - 59386 - [- - -]
#10 Default Completed - 59362 - [- - -]
#11 Default Completed - 59339 - [- - -]
#12 Default Completed - 59314 - [- - -]
#13 Default Completed - 59290 - [- - -]
Code:
sudo sas2flash -listallboards
LSI Corporation SAS2 Flash Utility
Version 20.00.00.00 (2014.09.18)
Copyright (c) 2008-2014 LSI Corporation. All rights reserved
Adapter Selected is a LSI SAS: SAS2116_1(B1)
Num Ctlr Board Name Serial Number
----------------------------------------------------
0 SAS2116_1(B1) SAS9201-16e N/A
Finished Processing Commands Successfully.
Exiting SAS2Flash.
