can anyone help me with the following smart test results? Overall seems to have passed? But the zfs pool is degraded. And not sure if "Self test Execution status:" means the last test was cancelled?
Code:
smartctl -a /dev/da1 smartctl 7.0 2018-12-30 r4883 [FreeBSD 11.3-RELEASE-p9 amd64] (local build) Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Red Device Model: WDC WD100EFAX-68LHPN0 Serial Number: 1DGPHVAZ LU WWN Device Id: 5 000cca 26cc9c74a Firmware Version: 83.H0A83 User Capacity: 10,000,831,348,736 bytes [10.0 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Jul 13 12:54:57 2020 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 93) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off supp ort. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: (1203) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_ FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0 2 Throughput_Performance 0x0004 129 129 054 Old_age Offline - 112 3 Spin_Up_Time 0x0007 154 154 024 Pre-fail Always - 417 (Average 439) 4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 3530 5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0 7 Seek_Error_Rate 0x000a 100 100 067 Old_age Always - 0 8 Seek_Time_Performance 0x0004 128 128 020 Old_age Offline - 18 9 Power_On_Hours 0x0012 098 098 000 Old_age Always - 18889 10 Spin_Retry_Count 0x0012 100 100 060 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 2925 22 Helium_Level 0x0023 100 100 025 Pre-fail Always - 100 192 Power-Off_Retract_Count 0x0032 097 097 000 Old_age Always - 4154 193 Load_Cycle_Count 0x0012 097 097 000 Old_age Always - 4154 194 Temperature_Celsius 0x0002 196 196 000 Old_age Always - 33 (Min/Max 22/54) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 8 SMART Error Log Version: 1 ATA Error Count: 8 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 8 occurred at disk power-on lifetime: 18642 hours (776 days + 18 hours) When the command that caused the error occurred, the device was active or idle . After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 04 00 99 ff 3f 40 00 37d+10:53:13.067 READ FPDMA QUEUED 2f 00 01 10 00 00 00 00 37d+10:53:13.059 READ LOG EXT 2f 00 01 10 00 00 00 00 37d+10:53:13.059 READ LOG EXT 60 04 00 99 ff 3f 40 00 37d+10:53:13.030 READ FPDMA QUEUED ef 10 02 00 00 00 00 00 37d+10:53:12.933 SET FEATURES [Enable SATA feature] Error 7 occurred at disk power-on lifetime: 18642 hours (776 days + 18 hours) When the command that caused the error occurred, the device was active or idle . After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 04 00 99 ff 3f 40 00 37d+10:53:13.059 READ FPDMA QUEUED ef 10 02 00 00 00 00 00 37d+10:53:12.933 SET FEATURES [Enable SATA feature] ef 02 00 00 00 00 00 00 37d+10:53:12.930 SET FEATURES [Enable write cache] ef aa 00 00 00 00 00 00 37d+10:53:12.927 SET FEATURES [Enable read look-ahea d] ef 03 46 00 00 00 00 00 37d+10:53:12.924 SET FEATURES [Set transfer mode] Error 6 occurred at disk power-on lifetime: 18642 hours (776 days + 18 hours) When the command that caused the error occurred, the device was active or idle . After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 01 00 d7 ff 3f 40 00 37d+10:53:12.601 READ FPDMA QUEUED 2f 00 01 10 00 00 00 00 37d+10:53:12.576 READ LOG EXT 2f 00 01 10 00 00 00 00 37d+10:53:12.576 READ LOG EXT 60 10 10 90 fc 3f 40 00 37d+10:53:12.569 READ FPDMA QUEUED 60 10 08 90 fa 3f 40 00 37d+10:53:12.569 READ FPDMA QUEUED Error 5 occurred at disk power-on lifetime: 18642 hours (776 days + 18 hours) When the command that caused the error occurred, the device was active or idle . After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 10 00 90 02 40 40 00 37d+10:53:12.576 READ FPDMA QUEUED 60 10 10 90 fc 3f 40 00 37d+10:53:12.569 READ FPDMA QUEUED 60 10 08 90 fa 3f 40 00 37d+10:53:12.569 READ FPDMA QUEUED 2f 00 01 10 00 00 00 00 37d+10:53:12.568 READ LOG EXT 2f 00 01 10 00 00 00 00 37d+10:53:12.568 READ LOG EXT Error 4 occurred at disk power-on lifetime: 18642 hours (776 days + 18 hours) When the command that caused the error occurred, the device was active or idle . After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 10 00 90 02 40 40 00 37d+10:53:12.568 READ FPDMA QUEUED 60 10 10 90 fc 3f 40 00 37d+10:53:12.560 READ FPDMA QUEUED 60 10 08 90 fa 3f 40 00 37d+10:53:12.560 READ FPDMA QUEUED 2f 00 01 10 00 00 00 00 37d+10:53:12.560 READ LOG EXT 2f 00 01 10 00 00 00 00 37d+10:53:12.560 READ LOG EXT SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA _of_first_error # 1 Short offline Interrupted (host reset) 50% 18876 - # 2 Short offline Interrupted (host reset) 50% 18852 - # 3 Extended offline Interrupted (host reset) 90% 18848 - # 4 Short offline Interrupted (host reset) 90% 18828 - # 5 Short offline Interrupted (host reset) 50% 18780 - # 6 Short offline Interrupted (host reset) 50% 18756 - # 7 Short offline Interrupted (host reset) 90% 18732 - # 8 Short offline Interrupted (host reset) 50% 18708 - # 9 Short offline Completed without error 00% 18684 - #10 Extended offline Interrupted (host reset) 90% 18684 - #11 Short offline Completed without error 00% 18660 - #12 Short offline Completed without error 00% 18636 - #13 Short offline Completed without error 00% 18612 - #14 Short offline Completed without error 00% 18588 - #15 Short offline Completed without error 00% 18564 - #16 Extended offline Completed without error 00% 18562 - #17 Short offline Completed without error 00% 18492 - #18 Short offline Completed without error 00% 18468 - #19 Short offline Completed without error 00% 18444 - #20 Short offline Completed without error 00% 18420 - #21 Short offline Completed without error 00% 18396 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
Last edited: