I know about the raidz1, I did not do the initial install. Fortunately, there is a backup of all the data.
Code:
smartctl 6.4 2015-06-04 r4109 [FreeBSD 10.3-RELEASE amd64] (local build)
Copyright (C) 2002-15, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Red
Device Model: WDC WD30EFRX-68EUZN0
Serial Number: WD-WCC4N5LAPTXK
LU WWN Device Id: 5 0014ee 2621e7904
Firmware Version: 82.00A82
User Capacity: 3,000,592,982,016 bytes [3.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Wed May 11 12:47:42 2016 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (39540) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 397) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x703d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0
3 Spin_Up_Time POS--K 173 173 021 - 6308
4 Start_Stop_Count -O--CK 100 100 000 - 16
5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0
7 Seek_Error_Rate -OSR-K 100 253 000 - 0
9 Power_On_Hours -O--CK 097 097 000 - 2243
10 Spin_Retry_Count -O--CK 100 253 000 - 0
11 Calibration_Retry_Count -O--CK 100 253 000 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 15
192 Power-Off_Retract_Count -O--CK 200 200 000 - 3
193 Load_Cycle_Count -O--CK 200 200 000 - 1549
194 Temperature_Celsius -O---K 109 107 000 - 41
196 Reallocated_Event_Count -O--CK 200 200 000 - 0
197 Current_Pending_Sector -O--CK 200 200 000 - 0
198 Offline_Uncorrectable ----CK 100 253 000 - 0
199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 5 Comprehensive SMART error log
0x03 GPL R/O 6 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 SATA NCQ Queued Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x21 GPL R/O 1 Write stream error log
0x22 GPL R/O 1 Read stream error log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
0xa8-0xb7 GPL,SL VS 1 Device vendor specific log
0xbd GPL,SL VS 1 Device vendor specific log
0xc0 GPL,SL VS 1 Device vendor specific log
0xc1 GPL VS 93 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 3054 (device log contains only the most recent 24 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 3054 [5] occurred at disk power-on lifetime: 1309 hours (54 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 00 46 00 00 00 00 00 00 40 00 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 03 00 46 00 00 00 00 00 00 40 00 5d+14:25:54.064 SET FEATURES [Set transfer mode]
ef 00 03 00 46 00 00 00 00 00 00 40 00 5d+14:25:54.061 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 00 00 00 00 00 40 00 5d+14:25:54.061 IDENTIFY DEVICE
b0 00 da 00 00 00 00 00 c2 4f 00 e0 00 5d+11:20:55.080 SMART RETURN STATUS
b0 00 d8 00 00 00 00 00 c2 4f 00 e0 00 5d+11:20:54.523 SMART ENABLE OPERATIONS
Error 3053 [4] occurred at disk power-on lifetime: 1309 hours (54 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 00 46 00 00 00 00 00 00 40 00 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 03 00 46 00 00 00 00 00 00 40 00 5d+14:25:54.061 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 00 00 00 00 00 40 00 5d+14:25:54.061 IDENTIFY DEVICE
b0 00 da 00 00 00 00 00 c2 4f 00 e0 00 5d+11:20:55.080 SMART RETURN STATUS
b0 00 d8 00 00 00 00 00 c2 4f 00 e0 00 5d+11:20:54.523 SMART ENABLE OPERATIONS
42 00 00 00 01 00 00 00 fa c5 3e e0 00 5d+11:20:46.513 READ VERIFY SECTOR(S) EXT
Error 3052 [3] occurred at disk power-on lifetime: 1306 hours (54 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 00 01 00 00 00 fa c5 3e e0 00 Device Fault; Error: ABRT at LBA = 0x00fac53e = 16434494
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
42 00 00 00 01 00 00 00 fa c5 3e e0 00 5d+11:20:46.513 READ VERIFY SECTOR(S) EXT
42 00 00 00 01 00 00 00 fa c5 3e e0 00 5d+11:20:37.998 READ VERIFY SECTOR(S) EXT
42 00 00 00 01 00 00 00 fa c5 3e e0 00 5d+11:20:29.483 READ VERIFY SECTOR(S) EXT
42 00 00 00 01 00 00 00 fa c5 3e e0 00 5d+11:20:20.968 READ VERIFY SECTOR(S) EXT
42 00 00 00 01 00 00 00 fa c5 3e e0 00 5d+11:20:12.453 READ VERIFY SECTOR(S) EXT
Error 3051 [2] occurred at disk power-on lifetime: 1306 hours (54 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 00 01 00 00 00 fa c5 3e e0 00 Device Fault; Error: ABRT at LBA = 0x00fac53e = 16434494
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
42 00 00 00 01 00 00 00 fa c5 3e e0 00 5d+11:20:37.998 READ VERIFY SECTOR(S) EXT
42 00 00 00 01 00 00 00 fa c5 3e e0 00 5d+11:20:29.483 READ VERIFY SECTOR(S) EXT
42 00 00 00 01 00 00 00 fa c5 3e e0 00 5d+11:20:20.968 READ VERIFY SECTOR(S) EXT
42 00 00 00 01 00 00 00 fa c5 3e e0 00 5d+11:20:12.453 READ VERIFY SECTOR(S) EXT
42 00 00 00 01 00 00 00 fa c5 3e e0 00 5d+11:20:03.938 READ VERIFY SECTOR(S) EXT
Error 3050 [1] occurred at disk power-on lifetime: 1306 hours (54 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 00 01 00 00 00 fa c5 3e e0 00 Device Fault; Error: ABRT at LBA = 0x00fac53e = 16434494
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
42 00 00 00 01 00 00 00 fa c5 3e e0 00 5d+11:20:29.483 READ VERIFY SECTOR(S) EXT
42 00 00 00 01 00 00 00 fa c5 3e e0 00 5d+11:20:20.968 READ VERIFY SECTOR(S) EXT
42 00 00 00 01 00 00 00 fa c5 3e e0 00 5d+11:20:12.453 READ VERIFY SECTOR(S) EXT
42 00 00 00 01 00 00 00 fa c5 3e e0 00 5d+11:20:03.938 READ VERIFY SECTOR(S) EXT
42 00 00 00 01 00 00 00 fa c5 3e e0 00 5d+11:19:55.423 READ VERIFY SECTOR(S) EXT
Error 3049 [0] occurred at disk power-on lifetime: 1306 hours (54 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 00 01 00 00 00 fa c5 3e e0 00 Device Fault; Error: ABRT at LBA = 0x00fac53e = 16434494
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
42 00 00 00 01 00 00 00 fa c5 3e e0 00 5d+11:20:20.968 READ VERIFY SECTOR(S) EXT
42 00 00 00 01 00 00 00 fa c5 3e e0 00 5d+11:20:12.453 READ VERIFY SECTOR(S) EXT
42 00 00 00 01 00 00 00 fa c5 3e e0 00 5d+11:20:03.938 READ VERIFY SECTOR(S) EXT
42 00 00 00 01 00 00 00 fa c5 3e e0 00 5d+11:19:55.423 READ VERIFY SECTOR(S) EXT
42 00 00 00 01 00 00 00 fa c5 3e e0 00 5d+11:19:46.908 READ VERIFY SECTOR(S) EXT
Error 3048 [23] occurred at disk power-on lifetime: 1306 hours (54 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 00 01 00 00 00 fa c5 3e e0 00 Device Fault; Error: ABRT at LBA = 0x00fac53e = 16434494
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
42 00 00 00 01 00 00 00 fa c5 3e e0 00 5d+11:20:12.453 READ VERIFY SECTOR(S) EXT
42 00 00 00 01 00 00 00 fa c5 3e e0 00 5d+11:20:03.938 READ VERIFY SECTOR(S) EXT
42 00 00 00 01 00 00 00 fa c5 3e e0 00 5d+11:19:55.423 READ VERIFY SECTOR(S) EXT
42 00 00 00 01 00 00 00 fa c5 3e e0 00 5d+11:19:46.908 READ VERIFY SECTOR(S) EXT
42 00 00 00 01 00 00 00 fa c5 3e e0 00 5d+11:19:38.393 READ VERIFY SECTOR(S) EXT
Error 3047 [22] occurred at disk power-on lifetime: 1306 hours (54 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 00 01 00 00 00 fa c5 3e e0 00 Device Fault; Error: ABRT at LBA = 0x00fac53e = 16434494
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
42 00 00 00 01 00 00 00 fa c5 3e e0 00 5d+11:20:03.938 READ VERIFY SECTOR(S) EXT
42 00 00 00 01 00 00 00 fa c5 3e e0 00 5d+11:19:55.423 READ VERIFY SECTOR(S) EXT
42 00 00 00 01 00 00 00 fa c5 3e e0 00 5d+11:19:46.908 READ VERIFY SECTOR(S) EXT
42 00 00 00 01 00 00 00 fa c5 3e e0 00 5d+11:19:38.393 READ VERIFY SECTOR(S) EXT
42 00 00 00 01 00 00 00 fa c5 3e e0 00 5d+11:19:29.878 READ VERIFY SECTOR(S) EXT
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 1153 -
# 2 Short offline Completed without error 00% 1057 -
# 3 Extended offline Completed without error 00% 825 -
# 4 Short offline Completed without error 00% 769 -
# 5 Short offline Completed without error 00% 650 -
# 6 Extended offline Completed without error 00% 489 -
# 7 Short offline Completed without error 00% 411 -
# 8 Short offline Completed without error 00% 315 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 258 (0x0102)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 41 Celsius
Power Cycle Min/Max Temperature: 37/41 Celsius
Lifetime Min/Max Temperature: 2/43 Celsius
Under/Over Temperature Limit Count: 0/0
Vendor specific:
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 478 (399)
Index Estimated Time Temperature Celsius
400 2016-05-11 04:50 41 **********************
... ..(148 skipped). .. **********************
71 2016-05-11 07:19 41 **********************
72 2016-05-11 07:20 37 ******************
... ..( 83 skipped). .. ******************
156 2016-05-11 08:44 37 ******************
157 2016-05-11 08:45 38 *******************
... ..( 22 skipped). .. *******************
180 2016-05-11 09:08 38 *******************
181 2016-05-11 09:09 39 ********************
... ..( 19 skipped). .. ********************
201 2016-05-11 09:29 39 ********************
202 2016-05-11 09:30 40 *********************
... ..( 25 skipped). .. *********************
228 2016-05-11 09:56 40 *********************
229 2016-05-11 09:57 41 **********************
... ..(169 skipped). .. **********************
399 2016-05-11 12:47 41 **********************
SCT Error Recovery Control:
Read: 70 (7.0 seconds)
Write: 70 (7.0 seconds)
Device Statistics (GP/SMART Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 12 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 11 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x8000 4 57189 Vendor specific
[root@filer] ~#