Raid10 - is this how it should look like?

[jackal077]

Sorry for the noob question. I've setup RAID10. I just wanna make sure that I've set it up correclty. Is this how it should look like?

Code:

[root@freenas ~]# zpool status                                                                                                     
  pool: Data                                                                                                                       
state: ONLINE                                                                                                                     
  scan: none requested                                                                                                             
config:                                                                                                                           
                                                                                                                                   
        NAME                                            STATE    READ WRITE CKSUM                                                 
        Data                                            ONLINE      0    0    0                                                 
          mirror-0                                      ONLINE      0    0    0                                                 
            gptid/df8051bd-848e-11e3-996d-0025b3a747d2  ONLINE      0    0    0                                                 
            gptid/dfff407d-848e-11e3-996d-0025b3a747d2  ONLINE      0    0    0                                                 
          mirror-1                                      ONLINE      0    0    0                                                 
            gptid/038dc991-848f-11e3-996d-0025b3a747d2  ONLINE      0    0    0                                                 
            gptid/0433b305-848f-11e3-996d-0025b3a747d2  ONLINE      0    0    0  

 

[Yatti420]

Can you post in code tags? Also please provide hardware specs etc.. For raid10 equivalent with ZFS you're doing mirrored pairs - striped?

 

[jackal077]

Sorry I didn't realize it will come out like that.
Hardware specs:
HP DL180 G6
RAM 24GB
4 x 4 TB Hard drives in RAID10

Code:

 pool: Data                                                                                                                       
state: ONLINE                                                                                                                     
  scan: none requested                                                                                                             
config:                                                                                                                           
                                                                                                                                   
        NAME                                            STATE    READ WRITE CKSUM                                                 
        Data                                            ONLINE      0    0    0                                                 
          mirror-0                                      ONLINE      0    0    0                                                 
            gptid/df8051bd-848e-11e3-996d-0025b3a747d2  ONLINE      0    0    0                                                 
            gptid/dfff407d-848e-11e3-996d-0025b3a747d2  ONLINE      0    0    0                                                 
          mirror-1                                      ONLINE      0    0    0                                                 
            gptid/038dc991-848f-11e3-996d-0025b3a747d2  ONLINE      0    0    0                                                 
            gptid/0433b305-848f-11e3-996d-0025b3a747d2  ONLINE      0    0    0 

 

[jackal077]

Can you post in code tags? Also please provide hardware specs etc.. For raid10 equivalent with ZFS you're doing mirrored pairs - striped?

What i did was:
Created a mirror with the first 2 drives and put a Volume name "Data"
then Created a 2nd mirror with the other 2 drives and from the drop down menu chose volume to extend "Data". I think this is the correct way of doing it, but I just want to make sure that everything is ok at this stage.

 

[Yatti420]

I believe so..

 

[Dusan]

What i did was:
Created a mirror with the first 2 drives and put a Volume name "Data"
then Created a 2nd mirror with the other 2 drives and from the drop down menu chose volume to extend "Data". I think this is the correct way of doing it, but I just want to make sure that everything is ok at this stage.

That works too, but you can also create it in one go by dragging the circular slider to get two rows of two drives.