Hi,
I set up a TrueNAS system around the second week of march, and i have JUST discovered that it has sent me a notification on 29th of March, that one of the drive is 'degraded because of persistent errors'.
Running zpool status -v results in:
and then i ran: smartctl -a /dev/ada3
is there anything i can do to help this? or should i just get a replacement drive?
Thank you!!
I set up a TrueNAS system around the second week of march, and i have JUST discovered that it has sent me a notification on 29th of March, that one of the drive is 'degraded because of persistent errors'.
Running zpool status -v results in:
Code:
root@truenas[~]# zpool status -v
pool: FirstPool
state: DEGRADED
status: One or more devices are faulted in response to persistent errors.
Sufficient replicas exist for the pool to continue functioning in a
degraded state.
action: Replace the faulted device, or use 'zpool clear' to mark the device
repaired.
scan: scrub repaired 0B in 00:14:59 with 0 errors on Sat Apr 17 00:14:59 2021
config:
NAME STATE READ WRITE CKSUM
FirstPool DEGRADED 0 0 0
raidz1-0 DEGRADED 0 0 0
gptid/85f8ce3a-7c14-11eb-a492-bc5ff4d6c187 ONLINE 0 0 0
gptid/86500d99-7c14-11eb-a492-bc5ff4d6c187 ONLINE 0 0 0
gptid/863a4c65-7c14-11eb-a492-bc5ff4d6c187 FAULTED 0 0 0 too many errors
errors: No known data errors
pool: boot-pool
state: ONLINE
scan: scrub repaired 0B in 00:00:11 with 0 errors on Thu May 6 03:45:11 2021
config:
NAME STATE READ WRITE CKSUM
boot-pool ONLINE 0 0 0
ada0p2 ONLINE 0 0 0
errors: No known data errors
and then i ran: smartctl -a /dev/ada3
Code:
root@truenas[~]# smartctl -a /dev/ada3
smartctl 7.1 2019-12-30 r5022 [FreeBSD 12.2-RELEASE-p3 amd64] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate IronWolf
Device Model: ST4000VN008-2DR166
Serial Number: ZGY8SF4R
LU WWN Device Id: 5 000c50 0c89770d8
Firmware Version: SC60
User Capacity: 4,000,787,030,016 bytes [4.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5980 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-3 T13/2161-D revision 5
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Fri May 7 22:18:27 2021 KST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 591) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 613) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x50bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 076 064 044 Pre-fail Always - 41823680
3 Spin_Up_Time 0x0003 095 095 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 9
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 079 060 045 Pre-fail Always - 74030916
9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 1499 (62 172 0)
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 11
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 065 059 040 Old_age Always - 35 (Min/Max 20/41)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 6
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 20
194 Temperature_Celsius 0x0022 035 041 000 Old_age Always - 35 (0 20 0 0 0)
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 1498 (76 208 0)
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 3528153642
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 447725359
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 1357 -
# 2 Extended offline Completed without error 00% 1340 -
# 3 Short offline Completed without error 00% 1189 -
# 4 Short offline Completed without error 00% 1021 -
# 5 Short offline Completed without error 00% 852 -
# 6 Short offline Completed without error 00% 684 -
# 7 Extended offline Completed without error 00% 620 -
# 8 Short offline Completed without error 00% 412 -
# 9 Short offline Completed without error 00% 244 -
#10 Short offline Completed without error 00% 76 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
is there anything i can do to help this? or should i just get a replacement drive?
Thank you!!
