bigbrovar
Cadet
- Joined
- Jul 11, 2023
- Messages
- 3
Hello people,
I am new here so I first one to apologies if I break any rules or did something that does not follow the forum etiquette. I read the rules and would follow them to the best of my knowledge, if I make a mistake kindly correct me and I would be guided.
I just completed my first TrueNAS build. The information about the Build is in my signature.
I got an error alert about 2 the disk that make up my Z1 Pool. Interestingly, although the pool was marked as degraded, all the disk that make up the pool were still marked as online. I ran a scrub of the pool and it came out with 0 errors.
Going through previous post here I noticed people with similar issues were advised to run a smart test. I ran a long smartctl test on the 2 drives with the alert and below are the result.
I am not sure what to make of this. Drive 1 /dev/ada5 is less than 2 years old and has rarely seen usage.
Drive 2 /dev/ada5 are much older drives.
Insight and advise would be appreciated.
I am new here so I first one to apologies if I break any rules or did something that does not follow the forum etiquette. I read the rules and would follow them to the best of my knowledge, if I make a mistake kindly correct me and I would be guided.
I just completed my first TrueNAS build. The information about the Build is in my signature.
I got an error alert about 2 the disk that make up my Z1 Pool. Interestingly, although the pool was marked as degraded, all the disk that make up the pool were still marked as online. I ran a scrub of the pool and it came out with 0 errors.
Going through previous post here I noticed people with similar issues were advised to run a smart test. I ran a long smartctl test on the 2 drives with the alert and below are the result.
DRIVE 1
/dev/ada5Code:
root@dune[~]# smartctl -a /dev/ada5
smartctl 7.2 2021-09-14 r5236 [FreeBSD 13.1-RELEASE-p7 amd64] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Red
Device Model: WDC WD80EFAX-68LHPN0
Serial Number: 2SG6W4DJ
LU WWN Device Id: 5 000cca 27dc3201d
Firmware Version: 83.H0A83
User Capacity: 8,001,563,222,016 bytes [8.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Wed Jul 12 05:45:39 2023 WAT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 93) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 983) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0
2 Throughput_Performance 0x0004 129 129 054 Old_age Offline - 112
3 Spin_Up_Time 0x0007 159 159 024 Pre-fail Always - 408 (Average 420)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 157
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000a 100 100 067 Old_age Always - 0
8 Seek_Time_Performance 0x0004 128 128 020 Old_age Offline - 18
9 Power_On_Hours 0x0012 099 099 000 Old_age Always - 9627
10 Spin_Retry_Count 0x0012 100 100 060 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 157
22 Helium_Level 0x0023 100 100 025 Pre-fail Always - 100
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 815
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 815
194 Temperature_Celsius 0x0002 154 154 000 Old_age Always - 42 (Min/Max 24/52)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 24
SMART Error Log Version: 1
ATA Error Count: 24 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 24 occurred at disk power-on lifetime: 8850 hours (368 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 20 97 20 d5 40 Error: ICRC, ABRT 32 sectors at LBA = 0x00d52097 = 13967511
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 00 b8 1f d5 40 08 4d+00:04:52.634 READ DMA EXT
ef 02 00 00 00 00 40 08 4d+00:04:52.611 SET FEATURES [Enable write cache]
ef aa 00 00 00 00 40 08 4d+00:04:52.608 SET FEATURES [Enable read look-ahead]
c6 00 10 00 00 00 40 08 4d+00:04:52.607 SET MULTIPLE MODE
ef 10 02 00 00 00 40 08 4d+00:04:52.604 SET FEATURES [Enable SATA feature]
Error 23 occurred at disk power-on lifetime: 8850 hours (368 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 90 78 36 d4 40 08 4d+00:04:37.442 READ FPDMA QUEUED
61 40 d8 38 33 d4 40 08 4d+00:04:37.430 WRITE FPDMA QUEUED
61 40 d0 b8 35 d4 40 08 4d+00:04:37.429 WRITE FPDMA QUEUED
61 40 c8 78 35 d4 40 08 4d+00:04:37.428 WRITE FPDMA QUEUED
61 10 c0 90 02 40 40 08 4d+00:04:37.427 WRITE FPDMA QUEUED
Error 22 occurred at disk power-on lifetime: 8850 hours (368 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 d8 70 a0 85 d3 40 08 4d+00:04:26.236 READ FPDMA QUEUED
61 40 e8 a0 83 d3 40 08 4d+00:04:26.225 WRITE FPDMA QUEUED
61 80 e0 e0 7d d3 40 08 4d+00:04:26.224 WRITE FPDMA QUEUED
61 08 d8 00 8f 82 40 08 4d+00:04:26.223 WRITE FPDMA QUEUED
61 40 d0 60 85 d3 40 08 4d+00:04:26.223 WRITE FPDMA QUEUED
Error 21 occurred at disk power-on lifetime: 8850 hours (368 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 d8 e0 15 d2 40 08 4d+00:04:03.006 READ FPDMA QUEUED
60 40 e8 20 22 d2 40 08 4d+00:04:02.979 READ FPDMA QUEUED
60 c0 e0 e0 1d d2 40 08 4d+00:04:02.979 READ FPDMA QUEUED
ef 02 00 00 00 00 40 08 4d+00:04:02.976 SET FEATURES [Enable write cache]
ef aa 00 00 00 00 40 08 4d+00:04:02.973 SET FEATURES [Enable read look-ahead]
Error 20 occurred at disk power-on lifetime: 8850 hours (368 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 40 f0 68 06 74 40 08 4d+00:00:25.006 READ FPDMA QUEUED
60 40 e8 28 06 74 40 08 4d+00:00:25.003 READ FPDMA QUEUED
60 40 e0 e8 05 74 40 08 4d+00:00:25.000 READ FPDMA QUEUED
60 40 d8 68 05 74 40 08 4d+00:00:24.897 READ FPDMA QUEUED
60 40 d0 a8 05 74 40 08 4d+00:00:24.893 READ FPDMA QUEUED
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 9621 -
# 2 Extended offline Completed without error 00% 9413 -
# 3 Extended offline Completed without error 00% 9268 -
# 4 Short offline Completed without error 00% 206 -
# 5 Short offline Completed without error 00% 200 -
# 6 Short offline Completed without error 00% 197 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.DRIVE 2
/dev/ada0Code:
root@dune[~]# smartctl -a /dev/ada0
smartctl 7.2 2021-09-14 r5236 [FreeBSD 13.1-RELEASE-p7 amd64] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: HGST Deskstar NAS
Device Model: HGST HDN728080ALE604
Serial Number: VLKWAZ0Y
LU WWN Device Id: 5 000cca 260f6b5b4
Firmware Version: A4GNW91X
User Capacity: 8,001,563,222,016 bytes [8.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Wed Jul 12 09:02:57 2023 WAT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 101) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: (1159) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0
2 Throughput_Performance 0x0005 134 134 054 Pre-fail Offline - 105
3 Spin_Up_Time 0x0007 150 150 024 Pre-fail Always - 452 (Average 427)
4 Start_Stop_Count 0x0012 099 099 000 Old_age Always - 7646
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 128 128 020 Pre-fail Offline - 18
9 Power_On_Hours 0x0012 096 096 000 Old_age Always - 33234
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 3532
22 Helium_Level 0x0023 100 100 025 Pre-fail Always - 100
192 Power-Off_Retract_Count 0x0032 081 081 000 Old_age Always - 23343
193 Load_Cycle_Count 0x0012 081 081 000 Old_age Always - 23343
194 Temperature_Celsius 0x0002 130 130 000 Old_age Always - 46 (Min/Max 17/51)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 530
SMART Error Log Version: 1
ATA Error Count: 530 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 530 occurred at disk power-on lifetime: 32854 hours (1368 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 08 80 88 4d 48 40 08 20d+17:01:28.915 WRITE FPDMA QUEUED
61 08 78 78 2e e9 40 08 20d+17:01:28.914 WRITE FPDMA QUEUED
61 10 70 70 1f 75 40 08 20d+17:01:28.913 WRITE FPDMA QUEUED
61 20 68 80 ec b3 40 08 20d+17:01:28.913 WRITE FPDMA QUEUED
61 08 60 80 4d 48 40 08 20d+17:01:28.912 WRITE FPDMA QUEUED
Error 529 occurred at disk power-on lifetime: 32848 hours (1368 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 48 68 88 04 81 40 08 20d+11:09:09.066 WRITE FPDMA QUEUED
61 10 60 50 ce 18 40 08 20d+11:09:09.065 WRITE FPDMA QUEUED
61 08 58 48 ce 18 40 08 20d+11:09:09.065 WRITE FPDMA QUEUED
61 08 50 40 ce 18 40 08 20d+11:09:09.065 WRITE FPDMA QUEUED
61 58 48 e8 cd 18 40 08 20d+11:09:09.064 WRITE FPDMA QUEUED
Error 528 occurred at disk power-on lifetime: 32848 hours (1368 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 28 28 d0 58 a7 40 08 20d+11:02:42.300 WRITE FPDMA QUEUED
61 20 20 20 29 45 40 08 20d+11:02:42.299 WRITE FPDMA QUEUED
61 30 18 20 40 e4 40 08 20d+11:02:42.299 WRITE FPDMA QUEUED
61 08 10 38 01 e5 40 08 20d+11:02:42.299 WRITE FPDMA QUEUED
61 08 08 28 64 0f 40 08 20d+11:02:42.298 WRITE FPDMA QUEUED
Error 527 occurred at disk power-on lifetime: 32846 hours (1368 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 18 18 e8 37 79 40 08 20d+09:28:48.864 WRITE FPDMA QUEUED
61 58 10 90 37 79 40 08 20d+09:28:48.863 WRITE FPDMA QUEUED
61 08 08 80 0d 12 40 08 20d+09:28:48.863 WRITE FPDMA QUEUED
61 10 00 70 0d 12 40 08 20d+09:28:48.863 WRITE FPDMA QUEUED
61 08 f8 68 0d 12 40 08 20d+09:28:48.863 WRITE FPDMA QUEUED
Error 526 occurred at disk power-on lifetime: 32845 hours (1368 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 70 28 c0 44 ad 40 08 20d+07:53:52.412 WRITE FPDMA QUEUED
61 10 20 d0 18 a7 40 08 20d+07:53:52.412 WRITE FPDMA QUEUED
61 18 18 70 8f 43 40 08 20d+07:53:52.411 WRITE FPDMA QUEUED
61 a8 10 78 ba e1 40 08 20d+07:53:52.411 WRITE FPDMA QUEUED
61 10 08 b0 3a 72 40 08 20d+07:53:52.411 WRITE FPDMA QUEUED
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 33228 -
# 2 Extended offline Aborted by host 80% 32115 -
# 3 Short offline Completed without error 00% 32111 -
# 4 Short offline Completed without error 00% 32087 -
# 5 Short offline Completed without error 00% 32063 -
# 6 Short offline Completed without error 00% 32039 -
# 7 Short offline Completed without error 00% 32015 -
# 8 Short offline Completed without error 00% 31991 -
# 9 Short offline Completed without error 00% 31967 -
#10 Extended offline Completed without error 00% 31964 -
#11 Short offline Completed without error 00% 31943 -
#12 Short offline Completed without error 00% 31919 -
#13 Short offline Completed without error 00% 31895 -
#14 Short offline Completed without error 00% 31871 -
#15 Short offline Completed without error 00% 31847 -
#16 Short offline Completed without error 00% 31823 -
#17 Short offline Completed without error 00% 31799 -
#18 Extended offline Completed without error 00% 31796 -
#19 Short offline Completed without error 00% 31775 -
#20 Short offline Completed without error 00% 31751 -
#21 Short offline Completed without error 00% 31727 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.I am not sure what to make of this. Drive 1 /dev/ada5 is less than 2 years old and has rarely seen usage.
Drive 2 /dev/ada5 are much older drives.
Insight and advise would be appreciated.
