BUILD JBOD Set Drive Volumes Don't Post In FREENAS

[united]

Completely Fresh hardware system and clean install of FreeNAS 10
FreeNAS 10 latest as of Feb 20th (US time)
Chassis: Supermicro 6048R-E1CR36H
RAID Controller: LSI3108 HW RAID
SATA Connected 24 x 8TB Drives
Drives are all set to JBOD not RAID and are completely new out of the bags

All drives are posting in BIOS with JBOD status, however I don't see these as available volumes inside FreeNAS
FYI, I am a nooby to FreeNAS and I may have missed a completely obvious step to have volumes show inside of FreeNAS.

=========================
Model Numbers for Hardware Build:
WD8002FRYZ WD Gold Edition,Enterprise 8TB 3.5 inch HDD, 128MB Cache ,7200 RPM SATA3 Hard Drive
SSG-6048R-E1CR36H Supermicro 6048R-E1CR36H Barebone 1 4,830.59 SuperStorage Server, 4U, 2x
LGA2011-3, 36x 3.5" Hot-Swap SAS3/SATA3,
LSI3108 HW RAID and expander backplanes, 2x 10GbE X540, 2x 1280W Redundant PSU
CT16G4DFD8213 Crucial 16GB DESKTOP DDR4 2133 MT/s 4 129.00 (PC4-17000) CL15 DR x8 Unbuffered DIMM 288pin DDR4 Platform ONLY
BX80644E52620V3 Intel Xeon E5-2620 v3 Processor,2.4GHz, 15MB 2 570.00 Cache, LGA2011-3, 6Core/12Thread,85W TDP
MFM1T02A-SR Mellanox optical module, ETH 10GbE, 10Gb/s, 2 144.79 SFP+, LC-LC, 850nm, SR up to 300m
MCX312B-XCCT Mellanox MCX312B-XCCT ConnectX-3 Pro EN 1 270.83 network interface card, 10GbE, dual-port SFP+, PCIe3.0 x8 8GT/s, RoHS R6
=========================

 

[Ericloewe]

There are a lot of things wrong here.

FreeNAS 10 latest as of Feb 20th (US time)

FYI, I am a nooby to FreeNAS

These two don't mix. Do not run beta software unless you know what you're doing.

RAID Controller: LSI3108 HW RAID

If you can't get rid of that thing and use an SAS3008, SAS2308 or SAS2008 in IT mode, the next-best thing is to stop using the archaic mfi driver and instead use the new mrsas driver, which does allow compatible SAS controllers (SAS3xxx and SAS2308) to present direct-attach drives to the OS even in HW RAID mode. You'll have to search the forum to find the correct procedure.

CT16G4DFD8213 Crucial 16GB DESKTOP DDR4 2133 MT/s 4 129.00 (PC4-17000) CL15 DR x8 Unbuffered DIMM 288pin DDR4 Platform ONLY

That's not ECC RAM. Given the rest of the system, I assume this was a mistake, so replace these with ECC DIMMs.

 

[united]

@Ericloewe I will investigate these hardware suggestions via our reseller this week. I really appreciate your input! : )

 

[united]

New Controller on the way! https://www.pbtech.co.nz/product/IDESPM1009/Supermicro-Add-on-card-AOC-S3008L-L8e-PCIe-Gen3-8

 

[Mr_N]

Much better :)

 

[united]

Happy to report the SAS3008 and Firmware version 13 controller solved all. I'm up and running: RESOLVED thanks to @Ericloewe

 

[Stux]

Check that you have ECC ram for a build of that class.

 

[united]

Check that you have ECC ram for a build of that class.

That was indeed a reseller typo, thank you for the reminder! : )