Hey, I'm using an old PC as a NAS (with TrueNAS ofc) and I have a WD Red Pro rev.2 (2tb) which is disconnecting from TrueNAS after 20 days (or so) of running 24/7. After a reboot, everything is working as normal. But on my pool status, it has as Pool Status: DEGRADED (but it is working fine). I also took it away from the PC and tested on my main machine with HDD Sentinel. No errors.
Here is my smartctl output:
Any idea of why is this happening?
Here is my smartctl output:
Code:
Handle 0x7F00, DMI type 127, 4 bytes
End Of Table
root@truenas[~]# smartctl -a /dev/ada1
smartctl 7.2 2020-12-30 r5155 [FreeBSD 12.2-RELEASE-p11 amd64] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Red Pro
Device Model: WDC WD2002FFSX-68PF8N0
Serial Number: WD-WCC6N4YZ8SH1
LU WWN Device Id: 5 0014ee 21453c886
Firmware Version: 81.00A81
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-3 T13/2161-D revision 5
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Sun Jul 10 15:49:31 2022 EEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 209) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x203d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 142 137 021 Pre-fail Always - 5866
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 34
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 091 091 000 Old_age Always - 6955
10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 34
16 Unknown_Attribute 0x0022 001 199 000 Old_age Always - 21389075343
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 24
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 15
194 Temperature_Celsius 0x0022 110 106 000 Old_age Always - 37
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0
SMART Error Log Version: 1
ATA Error Count: 149 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 149 occurred at disk power-on lifetime: 6583 hours (274 days + 7 hours)
When the command that caused the error occurred, the device was in an unknownstate.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 00 b0 8e 55 40 Error:
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
Error 148 occurred at disk power-on lifetime: 6583 hours (274 days + 7 hours)
When the command that caused the error occurred, the device was in an unknownstate.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 00 b0 8d 55 40 Error:
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
Error 147 occurred at disk power-on lifetime: 6583 hours (274 days + 7 hours)
When the command that caused the error occurred, the device was in an unknownstate.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 00 b8 4e 51 40 Error:
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
Error 146 occurred at disk power-on lifetime: 6581 hours (274 days + 5 hours)
When the command that caused the error occurred, the device was in an unknownstate.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 00 70 c3 53 40 Error:
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
Error 145 occurred at disk power-on lifetime: 6578 hours (274 days + 2 hours)
When the command that caused the error occurred, the device was in an unknownstate.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 41 00 90 83 54 40 Error:
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 6944 -
# 2 Extended offline Completed without error 00% 6920 -
# 3 Extended offline Completed without error 00% 6896 -
# 4 Extended offline Completed without error 00% 6872 -
# 5 Extended offline Completed without error 00% 6848 -
# 6 Extended offline Completed without error 00% 6824 -
# 7 Extended offline Completed without error 00% 6800 -
# 8 Extended offline Completed without error 00% 6776 -
# 9 Extended offline Completed without error 00% 6752 -
#10 Extended offline Completed without error 00% 6728 -
#11 Extended offline Completed without error 00% 6704 -
#12 Extended offline Completed without error 00% 6680 -
#13 Extended offline Completed without error 00% 6656 -
#14 Extended offline Completed without error 00% 6632 -
#15 Extended offline Completed without error 00% 6608 -
#16 Extended offline Interrupted (host reset) 50% 6583 -
#17 Extended offline Completed without error 00% 6561 -
#18 Extended offline Completed without error 00% 6537 -
#19 Extended offline Completed without error 00% 6513 -
#20 Extended offline Completed without error 00% 6489 -
#21 Extended offline Completed without error 00% 6465 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testingAny idea of why is this happening?
