Yup, I've done that too and I'm certain that value is listed in the instructions. For some reason I just like to reboot the system to ensure it is fully operational, not just to reset that value. I've run into the situation on many different computers where you make a change and 3+ days later your system reboots and something is wrong. Then you rack your brain to thing "what did I do and when did I do it?". So when I make changes, depending of course on the change, I like to reboot to ensure I didn't induce some failure. Again, that is just me.Well, that’s a perfectly valid way too, but you can just set t to its previous value too. I forget what it is, it the command will tell you when you change the value what it was before the change.
Odd but like @Stux said, maybe a firmware difference. It's too bad they all were not a zero value but having a value in thiese Fields does not mean anything bad if all the other results are good. So if you ran a SMART Long/Extended test at the end and all the critical parameters are good then I'd say move forward and continue with your installation.
ATA1 === START OF READ SMART DATA SECTION === SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 083 071 044 Pre-fail Always - 219249226 3 Spin_Up_Time 0x0003 093 093 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 16 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 074 060 045 Pre-fail Always - 23103751 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 149 (204 132 0) 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 16 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 077 072 040 Old_age Always - 23 (Min/Max 20/27) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 7 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 26 194 Temperature_Celsius 0x0022 023 040 000 Old_age Always - 23 (0 17 0 0 0) 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 148 (154 26 0) 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 31268770112 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 31256207701 ATA2 === START OF READ SMART DATA SECTION === SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 078 065 044 Pre-fail Always - 68684362 3 Spin_Up_Time 0x0003 093 093 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 16 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 074 060 045 Pre-fail Always - 23965414 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 149 (152 45 0) 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 16 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 078 073 040 Old_age Always - 22 (Min/Max 18/26) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 7 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 26 194 Temperature_Celsius 0x0022 022 040 000 Old_age Always - 22 (0 17 0 0 0) 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 148 (121 83 0) 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 31256148672 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 31256207547 ATA3 === START OF READ SMART DATA SECTION === SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 100 069 044 Pre-fail Always - 0 3 Spin_Up_Time 0x0003 093 093 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 16 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 074 060 045 Pre-fail Always - 24388700 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 149 (194 112 0) 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 16 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 078 073 040 Old_age Always - 22 (Min/Max 18/27) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 6 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 26 194 Temperature_Celsius 0x0022 022 040 000 Old_age Always - 22 (0 15 0 0 0) 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 148 (246 104 0) 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 31256148672 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 31256207547 ATA4 === START OF READ SMART DATA SECTION === SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 080 072 044 Pre-fail Always - 103421514 3 Spin_Up_Time 0x0003 093 093 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 16 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 074 060 045 Pre-fail Always - 23813692 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 149 (76 11 0) 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 16 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 078 073 040 Old_age Always - 22 (Min/Max 18/27) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 6 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 26 194 Temperature_Celsius 0x0022 022 040 000 Old_age Always - 22 (0 15 0 0 0) 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 148 (98 136 0) 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 31256148672 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 31256207547 ATA5 === START OF READ SMART DATA SECTION === SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 083 068 044 Pre-fail Always - 191092554 3 Spin_Up_Time 0x0003 093 093 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 16 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 074 060 045 Pre-fail Always - 26276842 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 149 (239 58 0) 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 16 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 075 070 040 Old_age Always - 25 (Min/Max 19/30) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 7 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 26 194 Temperature_Celsius 0x0022 025 040 000 Old_age Always - 25 (0 16 0 0 0) 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 148 (160 166 0) 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 31256148672 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 31256207547
Use smartctl -X to abort test. root@freenas:~ # smartctl -A /dev/ada1 smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.0-STABLE amd64] (local build) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF READ SMART DATA SECTION === SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 100 068 044 Pre-fail Always - 53786 3 Spin_Up_Time 0x0003 094 093 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 48 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 074 060 045 Pre-fail Always - 28031998 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 317 (81 169 0) 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 33 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 077 072 040 Old_age Always - 23 (Min/Max 22/23) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 13 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 133 194 Temperature_Celsius 0x0022 023 040 000 Old_age Always - 23 (0 15 0 0 0) 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 299 (165 28 0) 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 31268923094 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 46896512075 root@freenas:~ # smartctl -A /dev/ada2 smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.0-STABLE amd64] (local build) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF READ SMART DATA SECTION === SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 100 065 044 Pre-fail Always - 53785 3 Spin_Up_Time 0x0003 094 093 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 47 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 075 060 045 Pre-fail Always - 29105084 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 316 (146 222 0) 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 33 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 078 073 040 Old_age Always - 22 (Min/Max 21/22) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 13 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 132 194 Temperature_Celsius 0x0022 022 040 000 Old_age Always - 22 (0 15 0 0 0) 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 300 (219 93 0) 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 31256148674 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 46896396648 root@freenas:~ # smartctl -A /dev/ada3 smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.0-STABLE amd64] (local build) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF READ SMART DATA SECTION === SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 100 068 044 Pre-fail Always - 53785 3 Spin_Up_Time 0x0003 094 093 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 47 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 075 060 045 Pre-fail Always - 32041901 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 316 (160 209 0) 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 33 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 078 073 040 Old_age Always - 22 (Min/Max 21/22) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 13 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 133 194 Temperature_Celsius 0x0022 022 040 000 Old_age Always - 22 (0 14 0 0 0) 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 300 (115 208 0) 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 31256148674 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 46896396648 root@freenas:~ # smartctl -A /dev/ada4 smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.0-STABLE amd64] (local build) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF READ SMART DATA SECTION === SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 100 068 044 Pre-fail Always - 53786 3 Spin_Up_Time 0x0003 094 093 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 48 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 075 060 045 Pre-fail Always - 28923145 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 316 (135 1 0) 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 33 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 077 073 040 Old_age Always - 23 (Min/Max 21/23) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 12 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 133 194 Temperature_Celsius 0x0022 023 040 000 Old_age Always - 23 (0 14 0 0 0) 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 300 (191 236 0) 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 31256148674 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 46896396649 root@freenas:~ # smartctl -A /dev/ada5 smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.0-STABLE amd64] (local build) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF READ SMART DATA SECTION === SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 083 068 044 Pre-fail Always - 194369096 3 Spin_Up_Time 0x0003 094 093 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 46 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 075 060 045 Pre-fail Always - 31889564 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 316 (243 129 0) 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 33 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 075 070 040 Old_age Always - 25 (Min/Max 23/25) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 12 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 131 194 Temperature_Celsius 0x0022 025 040 000 Old_age Always - 25 (0 14 0 0 0) 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 301 (43 103 0) 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 31256148674 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 46896396648
Seatools likely caused the descrepancy. It's nothing to be alarmed about.I noticed another strange number - Start Stop Count is not same for all drives, is this normal?
The Raw Read Error Rate can be ignored if your drive always reports some wild number but you have no other errors. Check out my Hard Drive Troubleshooting Guide in my signature. If this value is always zero and now starts to creap up, you probably have an issue.Although numbers Raw Read Error Rate number are now lower, from 9 figure to 5. Except for one drive where it is still 9 figure.
You don't need a script to run any of these tests on any drive, I just finished doing these test via the manual way of following the first posting in this thread. I do know that some interfaces do not support smartctl but you can easily find that out. Badblocks should be well supported.Is the burn-in testing procedure the same for SAS as it is for SATA disks? The reason I ask is I found a script by Spearfoot that works great on SATA disks (I've got it running under Ubuntu on six SATA disks that's probable nearing the end of the badblocks portion), but he indicated it was never tested on SAS disks and that commands are different. The first issue I had was it wasn't creating proper log files - as it turns out, that part was due to different naming conventions in the '=== START OF INFORMATION SECTION ===' portion of the SAS and SATA disks, which are different - the script is looking for "Device Model", "Model Family" and "Serial Number", when the relevant values are "Product", "Vendor" and "Serial number" (note the lower case 'n' in 'Serial number' - that's how it is in the output for a SAS drive *shrug*. I'm not sure if the script is running properly, but because the log file doesn't update after the initial creation (It should, in theory, update within two minutes or so of the initial run), I have a suspicion something's tripping it up.
Any thoughts?
You don't need a script to run any of these tests on any drive, I just finished doing these test via the manual way of following the first posting in this thread. I do know that some interfaces do not support smartctl but you can easily find that out. Badblocks should be well supported.
I do understand that running a script can make testing time take less time overall if you are not available to manually check results and launch the tests but that dead time can also be valuable as well to check to see if your hard drives are constantly spining up/down or head loading is incrementing, so it's not a total waste.
If you do test out the script with SAS drives, post your results on how the script worked.
root@freenas:~ # badblocks -b 4096 -wsv -o "da4.bb" /dev/da4 Checking for bad blocks in read-write mode From block 0 to 488378644 Testing with pattern 0xaa: set_o_direct: Inappropriate ioctl for device 3.96% done, 5:34 elapsed. (0/19329273/0 errors)
badblocks -b 520 -ws /dev/da4
, and this is what it's looking like so far:root@freenas:~ # badblocks -b 520 -ws /dev/da4 > bb2.log Testing with pattern 0xaa: 2.42% done, 5:04 elapsed. (0/0/0 errors)
You need to change the block size on your disks. Here is how:Thanks. The original posts were more related to getting the tests to run on the drives, which is in line with the purpose of the thread. Now that I'm pretty sure I determined the cause of the issues I was having (I'm assuming the reason for the 'errors' is that the 512, 1024 and 4096 block sizes didn't line up evenly with the 520 byte blocks). Now that I've gotten where I am, I'll see what I can do with what I have and if I need more, then I'll open up a new thread. Hopefully what I've posted will help someone if they should stumble across similar issues.