whistlepigger
Dabbler
- Joined
- Jun 9, 2011
- Messages
- 15
Platform is Supermicro H8SSL-i, AMD Opteron 175 dual core 2.2GHz, 4 GB DDR PC3200 400MHz memory, Onboard 2x Broadcom NetXtreme 1000tx, Onboard ServerWorks HT1000 SATA150 controller, internal IDE Transcend 2GB flash drive, 4 SATA Hitachi DeskStar 3TB
The system was running 8.2.0-RELEASE-x64, and I attempted an upgrade to 8.3.0-RELEASE-x64 via GUI. System restarted but showed panic on restart and any subsequent restart. I did not have time to do extensive troubleshooting, and have reverted to 8.2.0-Release for now. However, I did one boot with the SATA disks removed and the system seemed to get past this panic point, indicated that it did some post-upgrade processing, and then powered down to reboot. Before it powered on, I re-inserted the SATA disks but on boot the system errored as before. I never got to try any addidtinal boot on 8.3.0 with the SATA drives removed.
Panic details (forgive the layout and hopefully no typos - this was copied from the screen):
...
ugen2.1: <0x1166> at usbus2
uhub2: <0x1166 EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
Fatal trap 12: page fault while in kernel mode
cpuid = 0; apic id = 00
fault virtual address = 0x0
fault code = supervisor read instruction, page not present
instruction pointer = 0x20:0x0
stack pointer = 0x28:0xffffff80000e0b10
frame pointer = 0x28:0xffffff80000e0b40
code segment = base 0x0, limit 0xfffff, type 0x1b
= DPL 0, pres 1, long 1, def32 0, gran 1
processor eflags = interrupt enabled, resume, IOPL = 0
current process = 12 (irq11: atapci0+)
[thread pid 12 tid 100030 ]
Steopped at 0: *** error reading from address 0 ***
db>
The system was running 8.2.0-RELEASE-x64, and I attempted an upgrade to 8.3.0-RELEASE-x64 via GUI. System restarted but showed panic on restart and any subsequent restart. I did not have time to do extensive troubleshooting, and have reverted to 8.2.0-Release for now. However, I did one boot with the SATA disks removed and the system seemed to get past this panic point, indicated that it did some post-upgrade processing, and then powered down to reboot. Before it powered on, I re-inserted the SATA disks but on boot the system errored as before. I never got to try any addidtinal boot on 8.3.0 with the SATA drives removed.
Panic details (forgive the layout and hopefully no typos - this was copied from the screen):
...
ugen2.1: <0x1166> at usbus2
uhub2: <0x1166 EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
Fatal trap 12: page fault while in kernel mode
cpuid = 0; apic id = 00
fault virtual address = 0x0
fault code = supervisor read instruction, page not present
instruction pointer = 0x20:0x0
stack pointer = 0x28:0xffffff80000e0b10
frame pointer = 0x28:0xffffff80000e0b40
code segment = base 0x0, limit 0xfffff, type 0x1b
= DPL 0, pres 1, long 1, def32 0, gran 1
processor eflags = interrupt enabled, resume, IOPL = 0
current process = 12 (irq11: atapci0+)
[thread pid 12 tid 100030 ]
Steopped at 0: *** error reading from address 0 ***
db>
