Disk Missing in GUI?

[SherpaPsy]

I have 4x4TB disks installed, all 4 (as well as the USB) are enumerated during boot:

Oct 1 16:13:22 basecamp kernel: da1 at mps0 bus 0 scbus0 target 2 lun 0
Oct 1 16:13:22 basecamp kernel: da1: <ATA WDC WD40EFRX-68W 0A80> Fixed Direct Access SCSI-6 device
Oct 1 16:13:22 basecamp kernel: da1: 600.000MB/s transfers
Oct 1 16:13:22 basecamp kernel: da1: Command Queueing enabled
Oct 1 16:13:22 basecamp kernel: da1: 3815447MB (7814037168 512 byte sectors: 255H 63S/T 486401C)
Oct 1 16:13:22 basecamp kernel: da1: quirks=0x8<4K>
Oct 1 16:13:22 basecamp kernel: da3 at mps0 bus 0 scbus0 target 4 lun 0
Oct 1 16:13:22 basecamp kernel: da3: <ATA WDC WD40EFRX-68W 0A80> Fixed Direct Access SCSI-6 device
Oct 1 16:13:22 basecamp kernel: da3: 600.000MB/s transfers
Oct 1 16:13:22 basecamp kernel: da3: Command Queueing enabled
Oct 1 16:13:22 basecamp kernel: da3: 3815447MB (7814037168 512 byte sectors: 255H 63S/T 486401C)
Oct 1 16:13:22 basecamp kernel: da3: quirks=0x8<4K>
Oct 1 16:13:22 basecamp kernel: da4 at umass-sim0 bus 0 scbus7 target 0 lun 0
Oct 1 16:13:22 basecamp kernel: da4: <SanDisk Cruzer 1.20> Removable Direct Access SCSI-5 device
Oct 1 16:13:22 basecamp kernel: da4: 40.000MB/s transfers
Oct 1 16:13:22 basecamp kernel: da4: 7633MB (15633408 512 byte sectors: 255H 63S/T 973C)
Oct 1 16:13:22 basecamp kernel: da4: quirks=0x2<NO_6_BYTE>
Oct 1 16:13:22 basecamp kernel: SMP: AP CPU #1 Launched!
Oct 1 16:13:22 basecamp kernel: Timecounter "TSC-low" frequency 1098193479 Hz quality 800
Oct 1 16:13:22 basecamp kernel: da2 at mps0 bus 0 scbus0 target 3 lun 0
Oct 1 16:13:22 basecamp kernel: da2: <ATA ST4000VN000-1H41 SC43> Fixed Direct Access SCSI-6 device
Oct 1 16:13:22 basecamp kernel: da2: 600.000MB/s transfers
Oct 1 16:13:22 basecamp kernel: da2: Command Queueing enabled
Oct 1 16:13:22 basecamp kernel: da2: 3815447MB (7814037168 512 byte sectors: 255H 63S/T 486401C)
Oct 1 16:13:22 basecamp kernel: da0 at mps0 bus 0 scbus0 target 1 lun 0
Oct 1 16:13:22 basecamp kernel: da0: <ATA ST4000VN000-1H41 SC43> Fixed Direct Access SCSI-6 device
Oct 1 16:13:22 basecamp kernel: da0: 600.000MB/s transfers
Oct 1 16:13:22 basecamp kernel: da0: Command Queueing enabled
Oct 1 16:13:22 basecamp kernel: da0: 3815447MB (7814037168 512 byte sectors: 255H 63S/T 486401C)

and but only 3 of the disk are displayed in the GUI? I have run smartctl -a /dev/da1 and all the information is there, but not in the GUI!

Running:
FreeNAS-9.1.1-RELEASE-x64 (a752d35)
On an HP Proliant Microserver G7 N54L with 16Gb of RAM and an IBM 1051 reflashed in HBA mode.

Disks are all 4TB NAS "quality"- 2 WD and 2 Seagate.

I'm pretty good with AIX and Linux, so if there's anything I can do to try to find out why its not showing up, I would be happy to try!

Thanks1

John

 

[SherpaPsy]

Strange, after creating my ZVF volume, when I tried to add a description to that disk, instead of saving that, it populated the serial number! Now all is good, though its a bit odd.