Been using Freenas for over a year never had a errors. Just got new hardware and it has been running for about three weeks.
These are two Seagate IronWolf 3TB in Raid 0. all the data is back up on other computers because of the new setup
one started throwing errors. Dont have a replacement disk. after finishing writing this pretty sure its a failure, just looking look for someone to to decode the error.
Thanks,
These are two Seagate IronWolf 3TB in Raid 0. all the data is back up on other computers because of the new setup
one started throwing errors. Dont have a replacement disk. after finishing writing this pretty sure its a failure, just looking look for someone to to decode the error.
Thanks,
Code:
Dec 16 08:28:57 freenas2 smartd[3053]: Device: /dev/da3 [SAT], 1400 Currently unreadable (pending) sectors Dec 16 08:28:57 freenas2 smartd[3053]: Device: /dev/da3 [SAT], 1400 Offline uncorrectable sectors smartctl 6.6 2017-11-05 r4594 [FreeBSD 11.1-STABLE amd64] (local build) Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate IronWolf Device Model: ST3000VN007-2E4166 LU WWN Device Id: 5 000c50 0b395b99f Firmware Version: SC60 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5900 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Dec 16 08:35:02 2018 PST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 107) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 388) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x10bd) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 094 094 006 Pre-fail Always - 56282806 3 Spin_Up_Time 0x0003 100 100 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 1 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 100 253 030 Pre-fail Always - 85517 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 367 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 1 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 030 030 000 Old_age Always - 70 188 Command_Timeout 0x0032 093 093 000 Old_age Always - 7 189 High_Fly_Writes 0x003a 001 001 000 Old_age Always - 205 190 Airflow_Temperature_Cel 0x0022 072 069 045 Old_age Always - 28 (Min/Max 20/31) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 1 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 2 194 Temperature_Celsius 0x0022 028 040 000 Old_age Always - 28 (0 20 0 0 0) 197 Current_Pending_Sector 0x0012 092 092 000 Old_age Always - 1400 198 Offline_Uncorrectable 0x0010 092 092 000 Old_age Offline - 1400 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 70 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 70 occurred at disk power-on lifetime: 359 hours (14 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: WP at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 61 00 98 ff ff ff 4f 00 14d+23:00:46.483 WRITE FPDMA QUEUED 61 00 00 ff ff ff 4f 00 14d+23:00:46.483 WRITE FPDMA QUEUED 61 00 00 ff ff ff 4f 00 14d+23:00:46.483 WRITE FPDMA QUEUED 61 00 00 ff ff ff 4f 00 14d+23:00:46.483 WRITE FPDMA QUEUED 61 00 00 ff ff ff 4f 00 14d+23:00:46.483 WRITE FPDMA QUEUED Error 69 occurred at disk power-on lifetime: 359 hours (14 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: WP at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 61 00 00 ff ff ff 4f 00 14d+23:00:36.972 WRITE FPDMA QUEUED 61 00 00 ff ff ff 4f 00 14d+23:00:36.972 WRITE FPDMA QUEUED 61 00 00 ff ff ff 4f 00 14d+23:00:36.972 WRITE FPDMA QUEUED 61 00 00 ff ff ff 4f 00 14d+23:00:36.972 WRITE FPDMA QUEUED 61 00 00 ff ff ff 4f 00 14d+23:00:36.972 WRITE FPDMA QUEUED Error 68 occurred at disk power-on lifetime: 359 hours (14 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: WP at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 61 00 00 ff ff ff 4f 00 14d+23:00:30.770 WRITE FPDMA QUEUED 61 00 10 ff ff ff 4f 00 14d+23:00:30.769 WRITE FPDMA QUEUED 61 00 10 ff ff ff 4f 00 14d+23:00:30.765 WRITE FPDMA QUEUED 60 00 00 ff ff ff 4f 00 14d+23:00:30.745 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 14d+23:00:30.745 READ FPDMA QUEUED Error 67 occurred at disk power-on lifetime: 359 hours (14 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 98 ff ff ff 4f 00 14d+23:00:19.746 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 14d+23:00:19.746 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 14d+23:00:19.746 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 14d+23:00:19.746 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 14d+23:00:19.746 READ FPDMA QUEUED Error 66 occurred at disk power-on lifetime: 359 hours (14 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 ff ff ff 0f Error: WP at LBA = 0x0fffffff = 268435455 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 61 00 10 90 02 40 40 00 14d+23:00:14.457 WRITE FPDMA QUEUED 60 00 10 ff ff ff 4f 00 14d+23:00:14.456 READ FPDMA QUEUED 60 00 10 ff ff ff 4f 00 14d+23:00:14.455 READ FPDMA QUEUED 60 00 10 90 02 40 40 00 14d+23:00:14.455 READ FPDMA QUEUED 60 00 00 ff ff ff 4f 00 14d+23:00:14.455 READ FPDMA QUEUED SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.