ATA error count increased from 0 to 1

[Hostigal]

in frenass say this: 21 de Enero de 2017 a las 04:59 - Device: /dev/da9 [SAT], ATA error count increased from 0 to 1

what does this mean?
It is important
Zpool is ok, I have to keep it in mind ??

 

[Sakuru]

It means that da9 encountered an error. Please provide the output of smartctl -a /dev/da9.

 

[Hostigal]

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
00 51 01 10 00 00 00 Error: at LBA = 0x00000010 = 16

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 18 00 d8 28 7a 00 00 03:42:31.688 READ FPDMA QUEUED
61 38 00 90 78 81 00 00 03:42:31.688 WRITE FPDMA QUEUED
61 38 00 58 78 81 00 00 03:42:31.688 WRITE FPDMA QUEUED
61 38 00 08 78 81 00 00 03:42:31.688 WRITE FPDMA QUEUED
61 38 00 90 77 81 00 00 03:42:31.688 WRITE FPDMA QUEUED

Error 1 occurred at disk power-on lifetime: 14689 hours (612 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
00 51 01 10 00 00 00 Error: at LBA = 0x00000010 = 16

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 08 d0 0f 4c 00 01 03:37:38.440 READ FPDMA QUEUED
60 18 00 88 ee ae 00 00 03:37:38.440 READ FPDMA QUEUED
60 18 00 10 ee ae 00 00 03:37:38.440 READ FPDMA QUEUED
61 38 00 70 63 9e 00 00 03:37:38.440 WRITE FPDMA QUEUED
61 38 00 38 63 9e 00 00 03:37:38.440 WRITE FPDMA QUEUED

SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]

Warning! SMART Selective Self-Test Log Structure error: invalid SMART checksum.
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
255 0 65535 Read_scanning was never started
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

 

[m0nkey_]

Looks like it's time to replace the drive.

 

[Hostigal]

But it is not in total failure, it indicates that at the time it suffered a failure, if it had a total failure, the freenas should warn, and the zpool would not say that all the disks are ok ??
thanks!!!