zpool status
scan: scrub repaired 0 in 10h57m with 0 errors on Sun Feb 28 10:57:46 2016
config:
NAME STATE READ WRITE CKSUM
Donsnetworkstorage ONLINE 0 0 0
raidz2-0 ONLINE 0 0 0
gpt/ad0 ONLINE 0 0 0
gpt/ad1 ONLINE 0 0 0
gpt/ad2 ONLINE 0 0 0
gpt/ad3 ONLINE 0 0 0
gpt/ad4 ONLINE 0 0 0
errors: No known data errors
pool: freenas-boot
state: ONLINE
scan: scrub repaired 0 in 0h1m with 0 errors on Thu Feb 25 03:46:26 2016
config:
NAME STATE READ WRITE CKSUM
freenas-boot ONLINE 0 0 0
gptid/73a1e3b8-089a-11e5-9d1f-6c626d3a4e60 ONLINE 0 0 0
errors: No known data errors
[root@freenas ~]#
when i run the last command (smart test?) it scrolls through and leaves a bunch of information i cant get to. but 2 of the discks come back with different info at the end then the others, the ones showing error in gui
ada0
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 380) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0
2 Throughput_Performance 0x0005 136 136 054 Pre-fail Offline - 95
3 Spin_Up_Time 0x0007 141 141 024 Pre-fail Always - 395 (Average 382)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 101
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 146 146 020 Pre-fail Offline - 29
9 Power_On_Hours 0x0012 095 095 000 Old_age Always - 41342
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 101
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 306
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 306
194 Temperature_Celsius 0x0002 214 214 000 Old_age Always - 28 (Min/Max 17/42)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
ada1
Error 29 occurred at disk power-on lifetime: 38298 hours (1595 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 8d 0d 03 1e 06 Error: ICRC, ABRT 141 sectors at LBA = 0x061e030d = 102630157
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 ac ee 02 1e 40 00 3d+18:56:54.089 READ DMA EXT
25 00 ab 43 02 1e 40 00 3d+18:56:54.088 READ DMA EXT
25 00 ac 97 01 1e 40 00 3d+18:56:54.087 READ DMA EXT
25 00 ab ec 00 1e 40 00 3d+18:56:54.086 READ DMA EXT
25 00 ab 40 00 1e 40 00 3d+18:56:54.085 READ DMA EXT
Error 28 occurred at disk power-on lifetime: 38297 hours (1595 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 4c f4 83 59 03 Error: ICRC, ABRT 76 sectors at LBA = 0x035983f4 = 56198132
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 ab 95 83 59 40 00 3d+18:09:04.153 READ DMA EXT
25 00 ab e9 82 59 40 00 3d+18:09:04.152 READ DMA EXT
25 00 ac 3d 82 59 40 00 3d+18:09:04.151 READ DMA EXT
25 00 ab 92 81 59 40 00 3d+18:09:04.150 READ DMA EXT
25 00 ac e6 80 59 40 00 3d+18:09:04.149 READ DMA EXT
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
ada2
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 375) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0
2 Throughput_Performance 0x0005 135 135 054 Pre-fail Offline - 98
3 Spin_Up_Time 0x0007 139 139 024 Pre-fail Always - 404 (Average 387)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 105
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 146 146 020 Pre-fail Offline - 29
9 Power_On_Hours 0x0012 095 095 000 Old_age Always - 41346
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 105
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 304
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 304
194 Temperature_Celsius 0x0002 214 214 000 Old_age Always - 28 (Min/Max 17/43)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
ada3
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 394) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0
2 Throughput_Performance 0x0005 136 136 054 Pre-fail Offline - 95
3 Spin_Up_Time 0x0007 141 141 024 Pre-fail Always - 395 (Average 381)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 105
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 148 148 020 Pre-fail Offline - 28
9 Power_On_Hours 0x0012 095 095 000 Old_age Always - 41347
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 105
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 301
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 301
194 Temperature_Celsius 0x0002 214 214 000 Old_age Always - 28 (Min/Max 17/43)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
ada4
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 1
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1 occurred at disk power-on lifetime: 40909 hours (1704 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 53 65 f6 1e 05 Error: UNC 83 sectors at LBA = 0x051ef665 = 85915237
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 ab 0d f6 1e 40 00 3d+12:59:25.418 READ DMA EXT
25 00 ac 61 f5 1e 40 00 3d+12:59:25.418 READ DMA EXT
25 00 ab b6 f4 1e 40 00 3d+12:59:25.417 READ DMA EXT
25 00 ab 0a f4 1e 40 00 3d+12:59:25.416 READ DMA EXT
25 00 ac 5e f3 1e 40 00 3d+12:59:25.375 READ DMA EXT
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Hope that is what you guys are looking for.
Thanks for the help!
Don