smartctl 7.2 2021-09-14 r5236 [FreeBSD 13.1-RELEASE-p7 amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Intel S4510/S4610/S4500/S4600 Series SSDs Device Model: INTEL SSDSC2KB038T8 Serial Number: PHYF150105AR3P8EGN LU WWN Device Id: 5 5cd2e4 1551facb5 Firmware Version: XCV10132 User Capacity: 3,840,755,982,336 bytes [3.84 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sat Mar 2 14:35:14 2024 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 576) seconds. Offline data collection capabilities: (0x79) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 2) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O--CK 100 100 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 2956 12 Power_Cycle_Count -O--CK 100 100 000 - 63 170 Available_Reservd_Space PO--CK 100 100 010 - 0 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 174 Unsafe_Shutdown_Count -O--CK 100 100 000 - 49 175 Power_Loss_Cap_Test PO--CK 100 100 010 - 2381 (63 65535) 183 SATA_Downshift_Count -O--CK 100 100 000 - 0 184 End-to-End_Error_Count PO--CK 100 100 090 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 190 Drive_Temperature -O---K 069 049 000 - 31 (Min/Max 26/51) 192 Unsafe_Shutdown_Count -O--CK 100 100 000 - 49 194 Temperature_Celsius -O---K 100 099 000 - 31 197 Pending_Sector_Count -O--C- 100 100 000 - 0 199 CRC_Error_Count -OSRCK 100 100 000 - 5 225 Host_Writes_32MiB -O--CK 100 100 000 - 14628 226 Workld_Media_Wear_Indic -O--CK 100 100 000 - 0 227 Workld_Host_Reads_Perc -O--CK 100 100 000 - 93 228 Workload_Minutes -O--CK 100 100 000 - 176441 232 Available_Reservd_Space PO--CK 100 100 010 - 0 233 Media_Wearout_Indicator -O--CK 100 100 000 - 0 234 Thermal_Throttle_Status -O--CK 100 100 000 - 0/0 235 Power_Loss_Cap_Test PO--CK 100 100 010 - 2381 (63 65535) 241 Host_Writes_32MiB -O--CK 100 100 000 - 14628 242 Host_Reads_32MiB -O--CK 100 100 000 - 229110 243 NAND_Writes_32MiB -O--CK 100 100 000 - 50327 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 8 Comprehensive SMART error log 0x03 GPL R/O 20 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 512 Current Device Internal Status Data log 0x25 GPL R/O 512 Saved Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xb8 GPL,SL VS 1 Device vendor specific log 0xb9 GPL VS 3336 Device vendor specific log 0xb9 SL VS 8 Device vendor specific log 0xba GPL VS 1280 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 8 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (20 sectors) Device Error Count: 5 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Warning! SMART Extended Comprehensive Error Log Structure error: invalid SMART checksum. Error 5 [4] occurred at disk power-on lifetime: 2882 hours (120 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 b8 00 00 07 9d a9 88 40 00 Error: ICRC, ABRT at LBA = 0x079da988 = 127773064 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 01 00 00 b8 00 00 07 9d a9 88 40 00 20d+05:57:28.366 WRITE FPDMA QUEUED 61 01 00 00 b0 00 00 07 9d a8 88 40 00 20d+05:57:28.366 WRITE FPDMA QUEUED 61 01 00 00 a8 00 00 07 9d a7 88 40 00 20d+05:57:28.366 WRITE FPDMA QUEUED 61 01 00 00 a0 00 00 07 9d a6 88 40 00 20d+05:57:28.365 WRITE FPDMA QUEUED 61 01 00 00 98 00 00 07 9d a5 88 40 00 20d+05:57:28.365 WRITE FPDMA QUEUED Error 4 [3] occurred at disk power-on lifetime: 2881 hours (120 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 48 00 00 05 5b 68 c0 40 00 Error: ICRC, ABRT at LBA = 0x055b68c0 = 89876672 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 01 00 00 48 00 00 05 5b 68 c0 40 00 20d+05:18:47.625 WRITE FPDMA QUEUED 61 01 00 00 40 00 00 05 5b 67 c0 40 00 20d+05:18:47.625 WRITE FPDMA QUEUED 61 01 00 00 38 00 00 05 5b 66 c0 40 00 20d+05:18:47.624 WRITE FPDMA QUEUED 61 01 00 00 30 00 00 05 5b 65 c0 40 00 20d+05:18:47.624 WRITE FPDMA QUEUED 61 01 00 00 28 00 00 05 5b 64 c0 40 00 20d+05:18:47.623 WRITE FPDMA QUEUED Error 3 [2] occurred at disk power-on lifetime: 2881 hours (120 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 c8 00 00 05 5b 10 a0 40 00 Error: ICRC, ABRT at LBA = 0x055b10a0 = 89854112 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 01 00 00 c8 00 00 05 5b 10 a0 40 00 20d+05:18:37.281 WRITE FPDMA QUEUED 61 01 00 00 c0 00 00 05 5b 0f a0 40 00 20d+05:18:37.281 WRITE FPDMA QUEUED 61 01 00 00 b8 00 00 05 5b 0e a0 40 00 20d+05:18:37.280 WRITE FPDMA QUEUED 61 01 00 00 b0 00 00 05 5b 0d a0 40 00 20d+05:18:37.280 WRITE FPDMA QUEUED 61 01 00 00 a8 00 00 05 5b 0c a0 40 00 20d+05:18:37.279 WRITE FPDMA QUEUED Error 2 [1] occurred at disk power-on lifetime: 2881 hours (120 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 48 00 00 05 46 a7 f8 40 00 Error: ICRC, ABRT at LBA = 0x0546a7f8 = 88516600 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 90 00 48 00 00 05 46 a7 f8 40 00 20d+04:46:59.134 WRITE FPDMA QUEUED 61 01 00 00 40 00 00 05 46 a6 f8 40 00 20d+04:46:59.134 WRITE FPDMA QUEUED 61 00 e0 00 38 00 00 05 46 a6 18 40 00 20d+04:46:59.134 WRITE FPDMA QUEUED 61 01 00 00 30 00 00 05 46 a5 18 40 00 20d+04:46:59.133 WRITE FPDMA QUEUED 61 00 f0 00 28 00 00 05 46 a4 28 40 00 20d+04:46:59.133 WRITE FPDMA QUEUED Error 1 [0] occurred at disk power-on lifetime: 2881 hours (120 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 d0 00 00 02 12 ea e0 40 00 Error: ICRC, ABRT at LBA = 0x0212eae0 = 34794208 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 01 00 00 d0 00 00 02 12 ea e0 40 00 20d+04:37:21.524 WRITE FPDMA QUEUED 61 01 00 00 c8 00 00 02 12 e9 e0 40 00 20d+04:37:21.523 WRITE FPDMA QUEUED 61 01 00 00 c0 00 00 02 12 e8 e0 40 00 20d+04:37:21.523 WRITE FPDMA QUEUED 61 01 00 00 b8 00 00 02 12 e7 e0 40 00 20d+04:37:21.522 WRITE FPDMA QUEUED 61 01 00 00 b0 00 00 02 12 e6 e0 40 00 20d+04:37:21.522 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 2941 - # 2 Short offline Completed without error 00% 2908 - # 3 Extended offline Completed without error 00% 2908 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 26/51 Celsius Lifetime Min/Max Temperature: 12/51 Celsius Specified Max Operating Temperature: 73 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 00 00 2c 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/73 Celsius Min/Max Temperature Limit: 0/73 Celsius Temperature History Size (Index): 478 (412) Index Estimated Time Temperature Celsius 413 2024-03-02 06:38 31 ************ ... ..( 54 skipped). .. ************ 468 2024-03-02 07:33 31 ************ 469 2024-03-02 07:34 32 ************* 470 2024-03-02 07:35 31 ************ ... ..(419 skipped). .. ************ 412 2024-03-02 14:35 31 ************ SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 63 --- Lifetime Power-On Resets 0x01 0x018 6 958692781 --- Logical Sectors Written 0x01 0x020 6 11766809 --- Number of Write Commands 0x01 0x028 6 15014999228 --- Logical Sectors Read 0x01 0x030 6 10408513 --- Number of Read Commands 0x01 0x038 6 2054173784 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 31 --- Current Temperature 0x05 0x010 1 30 --- Average Short Term Temperature 0x05 0x018 1 27 --- Average Long Term Temperature 0x05 0x020 1 50 --- Highest Temperature 0x05 0x028 1 24 --- Lowest Temperature 0x05 0x030 1 32 --- Highest Average Short Term Temperature 0x05 0x038 1 24 --- Lowest Average Short Term Temperature 0x05 0x040 1 28 --- Highest Average Long Term Temperature 0x05 0x048 1 27 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 73 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 124 --- Number of Hardware Resets 0x06 0x010 4 82 --- Number of ASR Events 0x06 0x018 4 5 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x000a 4 4 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS