smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.131+truenas] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Toshiba 3.5" MG03ACAxxx(Y) Enterprise HDD Device Model: TOSHIBA MG03ACA400 Serial Number: Y5K5K3N1F LU WWN Device Id: 5 000039 6ab900f53 Add. Product Id: DELL(tm) Firmware Version: FL2H User Capacity: 4,000,787,030,016 bytes [4.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Feb 8 19:37:32 2024 PST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Disabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 90) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 623) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 098 050 - 0 2 Throughput_Performance --S--- 100 100 000 - 0 3 Spin_Up_Time POS--K 100 100 001 - 11425 4 Start_Stop_Count -O--CK 100 100 000 - 156 5 Reallocated_Sector_Ct PO--CK 100 100 050 - 29 7 Seek_Error_Rate -O-R-- 100 100 000 - 0 8 Seek_Time_Performance --S--- 100 100 000 - 0 9 Power_On_Hours -O--CK 001 001 000 - 62289 10 Spin_Retry_Count -O--CK 103 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 156 192 Power-Off_Retract_Count -O--CK 100 100 000 - 148 193 Load_Cycle_Count -O--CK 100 100 000 - 174 194 Temperature_Celsius -O---K 100 100 000 - 28 (Min/Max 12/39) 196 Reallocated_Event_Count -O--CK 100 100 000 - 21 198 Offline_Uncorrectable ----CK 100 100 000 - 1 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 241 Total_LBAs_Written -O--CK 100 100 000 - 455206130397 242 Total_LBAs_Read -O--CK 100 100 000 - 2832648144072 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xdf GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (64 sectors) Device Error Count: 6 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 6 [5] occurred at disk power-on lifetime: 62182 hours (2590 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 08 00 01 ce f7 08 66 40 00 Error: UNC at LBA = 0x1cef70866 = 7767263334 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 e0 00 18 00 01 ce f7 0a 98 40 00 14d+20:14:57.123 READ FPDMA QUEUED 60 02 00 00 10 00 01 ce f7 08 98 40 00 14d+20:14:57.123 READ FPDMA QUEUED 60 02 00 00 08 00 01 ce f7 06 98 40 00 14d+20:14:57.123 READ FPDMA QUEUED 60 02 00 00 00 00 01 ce f7 04 98 40 00 14d+20:14:57.123 READ FPDMA QUEUED 60 01 e0 00 18 00 01 ce f7 02 b0 40 00 14d+20:14:56.426 READ FPDMA QUEUED Error 5 [4] occurred at disk power-on lifetime: 61537 hours (2564 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 20 00 01 cb 17 f2 39 40 00 Error: UNC at LBA = 0x1cb17f239 = 7702311481 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 b8 00 28 00 01 cb 18 04 38 40 00 12d+09:23:12.847 READ FPDMA QUEUED 60 02 00 00 18 00 01 cb 18 02 38 40 00 12d+09:23:12.847 READ FPDMA QUEUED 60 02 00 00 10 00 01 cb 18 00 38 40 00 12d+09:23:12.847 READ FPDMA QUEUED 60 02 00 00 00 00 01 cb 17 fe 38 40 00 12d+09:23:12.847 READ FPDMA QUEUED 60 01 c0 00 50 00 01 cb 17 fc 70 40 00 12d+09:23:12.378 READ FPDMA QUEUED Error 4 [3] occurred at disk power-on lifetime: 59858 hours (2494 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 00 00 01 d0 df ed 94 40 00 Error: UNC at LBA = 0x1d0dfed94 = 7799303572 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 58 00 28 00 01 d0 df ee 20 40 00 12d+21:11:16.783 READ FPDMA QUEUED 60 02 00 00 00 00 01 d0 df ec 20 40 00 12d+21:11:16.783 READ FPDMA QUEUED 60 01 d0 00 20 00 01 d0 df ea 48 40 00 12d+21:11:16.123 READ FPDMA QUEUED 60 02 00 00 18 00 01 d0 df e8 48 40 00 12d+21:11:16.122 READ FPDMA QUEUED 60 02 00 00 10 00 01 d0 df e6 48 40 00 12d+21:11:16.122 READ FPDMA QUEUED Error 3 [2] occurred at disk power-on lifetime: 57598 hours (2399 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 28 00 01 d0 e2 b3 fb 40 00 Error: UNC at LBA = 0x1d0e2b3fb = 7799485435 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 50 00 00 00 01 d0 e2 b7 40 40 00 18d+02:31:38.160 READ FPDMA QUEUED 60 00 50 00 40 00 01 d0 e2 b6 90 40 00 18d+02:31:37.893 READ FPDMA QUEUED 60 00 50 00 38 00 01 d0 e2 b5 d8 40 00 18d+02:31:37.893 READ FPDMA QUEUED 60 00 50 00 08 00 01 d0 e2 b6 e8 40 00 18d+02:31:37.893 READ FPDMA QUEUED 60 00 50 00 30 00 01 d0 e2 b5 80 40 00 18d+02:31:37.893 READ FPDMA QUEUED Error 2 [1] occurred at disk power-on lifetime: 56497 hours (2354 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 10 00 01 cf c6 cc a6 40 00 Error: UNC at LBA = 0x1cfc6cca6 = 7780879526 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 e0 00 10 00 01 cf c6 cb 78 40 00 21d+22:17:33.616 READ FPDMA QUEUED 60 02 00 00 00 00 01 cf c6 c9 78 40 00 21d+22:17:33.616 READ FPDMA QUEUED 60 02 00 00 08 00 01 cf c6 c7 78 40 00 21d+22:17:33.614 READ FPDMA QUEUED 60 02 00 00 00 00 01 cf c6 c5 78 40 00 21d+22:17:33.614 READ FPDMA QUEUED 60 01 e8 00 10 00 01 cf c6 c3 90 40 00 21d+22:17:32.614 READ FPDMA QUEUED Error 1 [0] occurred at disk power-on lifetime: 55655 hours (2318 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 28 00 01 c6 da 0b 1c 40 00 Error: UNC at LBA = 0x1c6da0b1c = 7631145756 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 b0 00 50 00 01 c6 da 1a 48 40 00 36d+13:54:08.826 READ FPDMA QUEUED 60 02 00 00 18 00 01 c6 da 18 48 40 00 36d+13:54:08.826 READ FPDMA QUEUED 60 02 00 00 10 00 01 c6 da 16 48 40 00 36d+13:54:08.826 READ FPDMA QUEUED 60 02 00 00 00 00 01 c6 da 14 48 40 00 36d+13:54:08.826 READ FPDMA QUEUED 60 01 e0 00 48 00 01 c6 da 12 68 40 00 36d+13:54:08.003 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 54776 - # 2 Short offline Completed without error 00% 51999 - # 3 Short offline Completed without error 00% 22375 - # 4 Short offline Completed without error 00% 22317 - # 5 Short offline Completed without error 00% 9 - # 6 Vendor (0xdf) Completed without error 00% 8 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 27 Celsius Power Cycle Min/Max Temperature: 13/33 Celsius Lifetime Min/Max Temperature: 12/39 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/55 Celsius Min/Max Temperature Limit: 5/55 Celsius Temperature History Size (Index): 478 (320) Index Estimated Time Temperature Celsius 321 2024-02-08 11:40 27 ******** ... ..( 58 skipped). .. ******** 380 2024-02-08 12:39 27 ******** 381 2024-02-08 12:40 28 ********* ... ..( 97 skipped). .. ********* 1 2024-02-08 14:18 28 ********* 2 2024-02-08 14:19 27 ******** 3 2024-02-08 14:20 28 ********* ... ..(312 skipped). .. ********* 316 2024-02-08 19:33 28 ********* 317 2024-02-08 19:34 27 ******** 318 2024-02-08 19:35 28 ********* 319 2024-02-08 19:36 27 ******** 320 2024-02-08 19:37 28 ********* SCT Error Recovery Control: Read: 80 (8.0 seconds) Write: 80 (8.0 seconds) Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 156 --- Lifetime Power-On Resets 0x01 0x010 4 62289 --- Power-on Hours 0x01 0x018 6 455206130397 --- Logical Sectors Written 0x01 0x020 6 1015109487 --- Number of Write Commands 0x01 0x028 6 2832648144072 --- Logical Sectors Read 0x01 0x030 6 5812471491 --- Number of Read Commands 0x02 ===== = = === == Free-Fall Statistics (rev 1) == 0x02 0x010 4 0 --- Overlimit Shock Events 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 62288 --- Spindle Motor Power-on Hours 0x03 0x010 4 62518 --- Head Flying Hours 0x03 0x018 4 174 --- Head Load Events 0x03 0x020 4 29 --- Number of Reallocated Logical Sectors 0x03 0x028 4 48 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 6 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 1 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 28 --- Current Temperature 0x05 0x010 1 27 N-- Average Short Term Temperature 0x05 0x018 1 26 N-- Average Long Term Temperature 0x05 0x020 1 39 --- Highest Temperature 0x05 0x028 1 12 --- Lowest Temperature 0x05 0x030 1 35 N-- Highest Average Short Term Temperature 0x05 0x038 1 24 N-- Lowest Average Short Term Temperature 0x05 0x040 1 32 N-- Highest Average Long Term Temperature 0x05 0x048 1 25 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 55 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 5 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 393 --- Number of Hardware Resets 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 103 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0008 4 0 Device-to-host non-data FIS retries 0x000a 4 1 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS