+--------------------------------------------------------------------------------+
+                                     SMART                                      +
+--------------------------------------------------------------------------------+
/dev/ada1
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p10 amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Device Model:     SAMSUNG MZ7WD960HMHP-00003
Serial Number:    S1E4NYAFA01902
LU WWN Device Id: 5 002538 50023a0e5
Firmware Version: DXV8C03Q
User Capacity:    960,197,124,096 bytes [960 GB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    Solid State Device
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   ACS-2, ATA8-ACS T13/1699-D revision 4c
SATA Version is:  SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Wed Mar 25 09:49:02 2015 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Unavailable
APM feature is:   Unavailable
Rd look-ahead is: Enabled
Write cache is:   Enabled
ATA Security is:  Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		( 4200) seconds.
Offline data collection
capabilities: 			 (0x53) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					No Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 (  70) minutes.
SCT capabilities: 	       (0x003d)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  5 Reallocated_Sector_Ct   PO--CK   100   100   010    -    0
  9 Power_On_Hours          -O--CK   099   099   000    -    2541
 12 Power_Cycle_Count       -O--CK   099   099   000    -    38
177 Wear_Leveling_Count     PO--C-   099   099   005    -    15
179 Used_Rsvd_Blk_Cnt_Tot   PO--C-   100   100   010    -    0
180 Unused_Rsvd_Blk_Cnt_Tot PO--C-   100   100   010    -    7040
181 Program_Fail_Cnt_Total  -O--CK   100   100   000    -    0
182 Erase_Fail_Count_Total  -O--CK   100   100   000    -    0
183 Runtime_Bad_Block       PO--C-   100   100   010    -    0
184 End-to-End_Error        PO--CK   100   100   097    -    0
187 Reported_Uncorrect      -O--CK   100   100   000    -    0
190 Airflow_Temperature_Cel -O--CK   074   074   000    -    26
195 Hardware_ECC_Recovered  -O-RC-   200   200   000    -    0
199 UDMA_CRC_Error_Count    -OSRCK   100   100   000    -    0
202 Unknown_SSD_Attribute   PO--CK   100   100   010    -    0
235 Unknown_Attribute       -O--C-   099   099   000    -    24
241 Total_LBAs_Written      -O--CK   099   099   000    -    6232673097
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01       GPL,SL  R/O      1  Summary SMART error log
0x02       GPL,SL  R/O      1  Comprehensive SMART error log
0x03       GPL,SL  R/O      1  Ext. Comprehensive SMART error log
0x06       GPL,SL  R/O      1  SMART self-test log
0x07       GPL,SL  R/O      1  Extended self-test log
0x09       GPL,SL  R/W      1  Selective self-test log
0x10       GPL,SL  R/O      1  NCQ Command Error log
0x11       GPL,SL  R/O      1  SATA Phy Event Counters
0x30       GPL,SL  R/O      1  IDENTIFY DEVICE data log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xa0       GPL,SL  VS      16  Device vendor specific log

SMART Extended Comprehensive Error Log Version: 1 (1 sectors)
No Errors Logged

SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
  255        0    65535  Read_scanning was never started
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  3
SCT Version (vendor specific):       256 (0x0100)
SCT Support Level:                   1
Device State:                        SCT command executing in background (5)
Current Temperature:                    26 Celsius
Power Cycle Min/Max Temperature:     26/27 Celsius
Lifetime    Min/Max Temperature:      0/70 Celsius
Under/Over Temperature Limit Count:   0/0

SCT Temperature History Version:     3 (Unknown, should be 2)
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:      0/70 Celsius
Min/Max Temperature Limit:            0/70 Celsius
Temperature History Size (Index):    128 (6)

Index    Estimated Time   Temperature Celsius
   7    2015-03-25 07:42    26  *******
 ...    ..(126 skipped).    ..  *******
   6    2015-03-25 09:49    26  *******

SCT Error Recovery Control:
           Read: Disabled
          Write: Disabled

Device Statistics (GP Log 0x04) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  2            0  Command failed due to ICRC error
0x0002  2            0  R_ERR response for data FIS
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0005  2            0  R_ERR response for non-data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS
0x0008  2            0  Device-to-host non-data FIS retries
0x0009  2            5  Transition from drive PhyRdy to drive PhyNRdy
0x000a  2            9  Device-to-host register FISes sent due to a COMRESET
0x000b  2            0  CRC errors within host-to-device FIS
0x000d  2            0  Non-CRC errors within host-to-device FIS
0x000f  2            0  R_ERR response for host-to-device data FIS, CRC
0x0010  2            0  R_ERR response for host-to-device data FIS, non-CRC
0x0012  2            0  R_ERR response for host-to-device non-data FIS, CRC
0x0013  2            0  R_ERR response for host-to-device non-data FIS, non-CRC

/dev/ada0
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p10 amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Intel 730 and DC S3500/S3700 Series SSDs
Device Model:     INTEL SSDSC2BA100G3
Serial Number:    BTTV434403FP100FGN
LU WWN Device Id: 5 5cd2e4 04b6c91f7
Firmware Version: 5DV10270
User Capacity:    100,030,242,816 bytes [100 GB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    Solid State Device
Form Factor:      2.5 inches
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ACS-2 T13/2015-D revision 3
SATA Version is:  SATA 2.6, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Wed Mar 25 09:49:02 2015 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Unavailable
APM feature is:   Unavailable
Rd look-ahead is: Enabled
Write cache is:   Enabled
ATA Security is:  Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(    0) seconds.
Offline data collection
capabilities: 			 (0x79) SMART execute Offline immediate.
					No Auto Offline data collection support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 (   2) minutes.
Conveyance self-test routine
recommended polling time: 	 (   2) minutes.
SCT capabilities: 	       (0x003d)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  5 Reallocated_Sector_Ct   -O--CK   100   100   000    -    0
  9 Power_On_Hours          -O--CK   100   100   000    -    2539
 12 Power_Cycle_Count       -O--CK   100   100   000    -    32
170 Available_Reservd_Space PO--CK   100   100   010    -    0
171 Program_Fail_Count      -O--CK   100   100   000    -    0
172 Erase_Fail_Count        -O--CK   100   100   000    -    0
174 Unsafe_Shutdown_Count   -O--CK   100   100   000    -    17
175 Power_Loss_Cap_Test     PO--CK   100   100   010    -    637 (13 2612)
183 SATA_Downshift_Count    -O--CK   100   100   000    -    0
184 End-to-End_Error        PO--CK   100   100   090    -    0
187 Reported_Uncorrect      -O--CK   100   100   000    -    0
190 Temperature_Case        -O---K   077   075   000    -    23 (Min/Max 21/28)
192 Unsafe_Shutdown_Count   -O--CK   100   100   000    -    17
194 Temperature_Internal    -O---K   100   100   000    -    30
197 Current_Pending_Sector  -O--CK   100   100   000    -    0
199 CRC_Error_Count         -OSRCK   100   100   000    -    0
225 Host_Writes_32MiB       -O--CK   100   100   000    -    126700
226 Workld_Media_Wear_Indic -O--CK   100   100   000    -    102
227 Workld_Host_Reads_Perc  -O--CK   100   100   000    -    1
228 Workload_Minutes        -O--CK   100   100   000    -    152130
232 Available_Reservd_Space PO--CK   100   100   010    -    0
233 Media_Wearout_Indicator -O--CK   100   100   000    -    0
234 Thermal_Throttle        -O--CK   100   100   000    -    0/0
241 Host_Writes_32MiB       -O--CK   100   100   000    -    126700
242 Host_Reads_32MiB        -O--CK   100   100   000    -    1408
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01       GPL,SL  R/O      1  Summary SMART error log
0x02       GPL,SL  R/O      8  Comprehensive SMART error log
0x03       GPL,SL  R/O     20  Ext. Comprehensive SMART error log
0x04       GPL,SL  R/O      8  Device Statistics log
0x06       GPL,SL  R/O      1  SMART self-test log
0x07       GPL,SL  R/O      2  Extended self-test log
0x09       GPL,SL  R/W      1  Selective self-test log
0x10       GPL,SL  R/O      1  NCQ Command Error log
0x11       GPL,SL  R/O      1  SATA Phy Event Counters
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xb0       GPL,SL  VS       1  Device vendor specific log
0xb1       GPL,SL  VS      33  Device vendor specific log
0xdd       GPL,SL  VS       1  Device vendor specific log
0xde       GPL     VS     768  Device vendor specific log
0xdf       GPL     VS    1152  Device vendor specific log
0xdf       SL      VS     128  Device vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (20 sectors)
No Errors Logged

SMART Extended Self-test Log Version: 1 (2 sectors)
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  3
SCT Version (vendor specific):       1 (0x0001)
SCT Support Level:                   0
Device State:                        Active (0)
Current Temperature:                    23 Celsius
Power Cycle Min/Max Temperature:     21/28 Celsius
Lifetime    Min/Max Temperature:      4/39 Celsius
Under/Over Temperature Limit Count:   0/0

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:      0/70 Celsius
Min/Max Temperature Limit:            0/70 Celsius
Temperature History Size (Index):    478 (372)

Index    Estimated Time   Temperature Celsius
 373    2015-03-25 01:52    22  ***
 ...    ..( 67 skipped).    ..  ***
 441    2015-03-25 03:00    22  ***
 442    2015-03-25 03:01    21  **
 443    2015-03-25 03:02    21  **
 444    2015-03-25 03:03    22  ***
 445    2015-03-25 03:04    22  ***
 446    2015-03-25 03:05    21  **
 ...    ..(  7 skipped).    ..  **
 454    2015-03-25 03:13    21  **
 455    2015-03-25 03:14    22  ***
 456    2015-03-25 03:15    21  **
 457    2015-03-25 03:16    22  ***
 ...    ..( 57 skipped).    ..  ***
  37    2015-03-25 04:14    22  ***
  38    2015-03-25 04:15    21  **
  39    2015-03-25 04:16    21  **
  40    2015-03-25 04:17    21  **
  41    2015-03-25 04:18    22  ***
  42    2015-03-25 04:19    22  ***
  43    2015-03-25 04:20    22  ***
  44    2015-03-25 04:21    21  **
  45    2015-03-25 04:22    22  ***
 ...    ..(310 skipped).    ..  ***
 356    2015-03-25 09:33    22  ***
 357    2015-03-25 09:34    23  ****
 358    2015-03-25 09:35    22  ***
 ...    ..(  3 skipped).    ..  ***
 362    2015-03-25 09:39    22  ***
 363    2015-03-25 09:40    23  ****
 ...    ..(  3 skipped).    ..  ****
 367    2015-03-25 09:44    23  ****
 368    2015-03-25 09:45    22  ***
 369    2015-03-25 09:46    22  ***
 370    2015-03-25 09:47    23  ****
 371    2015-03-25 09:48    23  ****
 372    2015-03-25 09:49    23  ****

SCT Error Recovery Control:
           Read: Disabled
          Write: Disabled

Device Statistics (GP Log 0x04)
Page Offset Size         Value  Description
  1  =====  =                =  == General Statistics (rev 2) ==
  1  0x008  4               32  Lifetime Power-On Resets
  1  0x018  6       8303421427  Logical Sectors Written
  1  0x020  6        104133483  Number of Write Commands
  1  0x028  6         92291274  Logical Sectors Read
  1  0x030  6          4227685  Number of Read Commands
  4  =====  =                =  == General Errors Statistics (rev 1) ==
  4  0x008  4                0  Number of Reported Uncorrectable Errors
  4  0x010  4                0  Resets Between Cmd Acceptance and Completion
  5  =====  =                =  == Temperature Statistics (rev 1) ==
  5  0x008  1               23  Current Temperature
  5  0x010  1               22  Average Short Term Temperature
  5  0x018  1               22  Average Long Term Temperature
  5  0x020  1               34  Highest Temperature
  5  0x028  1               20  Lowest Temperature
  5  0x030  1               28  Highest Average Short Term Temperature
  5  0x038  1               21  Lowest Average Short Term Temperature
  5  0x040  1               26  Highest Average Long Term Temperature
  5  0x048  1               21  Lowest Average Long Term Temperature
  5  0x050  4                0  Time in Over-Temperature
  5  0x058  1               70  Specified Maximum Operating Temperature
  5  0x060  4                0  Time in Under-Temperature
  5  0x068  1                0  Specified Minimum Operating Temperature
  6  =====  =                =  == Transport Statistics (rev 1) ==
  6  0x008  4              204  Number of Hardware Resets
  6  0x010  4               88  Number of ASR Events
  6  0x018  4                0  Number of Interface CRC Errors
  7  =====  =                =  == Solid State Device Statistics (rev 1) ==
  7  0x008  1                0  Percentage Used Endurance Indicator

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  4            0  Command failed due to ICRC error
0x0003  4            0  R_ERR response for device-to-host data FIS
0x0004  4            0  R_ERR response for host-to-device data FIS
0x0006  4            0  R_ERR response for device-to-host non-data FIS
0x000a  4            6  Device-to-host register FISes sent due to a COMRESET
0x000b  4            0  CRC errors within host-to-device FIS
0x000d  4            0  Non-CRC errors within host-to-device FIS

/dev/da16
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p10 amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org

/dev/da16: Unknown USB bridge [0x0951:0x1666 (0x100)]
Please specify device type with the -d option.

Use smartctl -h to get a usage summary

/dev/da15
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p10 amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org

/dev/da15: Unknown USB bridge [0x0951:0x1666 (0x100)]
Please specify device type with the -d option.

Use smartctl -h to get a usage summary

/dev/da14
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p10 amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda 7200.14 (AF)
Device Model:     ST3000DM001-9YN166
Serial Number:    Z1F15DNG
LU WWN Device Id: 5 000c50 04e46d87e
Firmware Version: CC4H
User Capacity:    3,000,592,982,016 bytes [3.00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    7200 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Wed Mar 25 09:49:02 2015 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Unavailable
APM level is:     128 (minimum power consumption without standby)
Rd look-ahead is: Enabled
Write cache is:   Enabled
ATA Security is:  Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Unavailable

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(  592) seconds.
Offline data collection
capabilities: 			 (0x73) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					No Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 ( 338) minutes.
Conveyance self-test routine
recommended polling time: 	 (   2) minutes.
SCT capabilities: 	       (0x3085)	SCT Status supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR--   114   099   006    -    81364904
  3 Spin_Up_Time            PO----   092   092   000    -    0
  4 Start_Stop_Count        -O--CK   100   100   020    -    27
  5 Reallocated_Sector_Ct   PO--CK   100   100   036    -    0
  7 Seek_Error_Rate         POSR--   083   060   030    -    215413491
  9 Power_On_Hours          -O--CK   082   082   000    -    16070
 10 Spin_Retry_Count        PO--C-   100   100   097    -    0
 12 Power_Cycle_Count       -O--CK   100   100   020    -    27
183 Runtime_Bad_Block       -O--CK   100   100   000    -    0
184 End-to-End_Error        -O--CK   100   100   099    -    0
187 Reported_Uncorrect      -O--CK   100   100   000    -    0
188 Command_Timeout         -O--CK   100   100   000    -    1 1 1
189 High_Fly_Writes         -O-RCK   032   032   000    -    68
190 Airflow_Temperature_Cel -O---K   077   067   045    -    23 (Min/Max 23/24)
191 G-Sense_Error_Rate      -O--CK   100   100   000    -    0
192 Power-Off_Retract_Count -O--CK   100   100   000    -    25
193 Load_Cycle_Count        -O--CK   086   086   000    -    29058
194 Temperature_Celsius     -O---K   023   040   000    -    23 (0 20 0 0 0)
197 Current_Pending_Sector  -O--C-   100   100   000    -    0
198 Offline_Uncorrectable   ----C-   100   100   000    -    0
199 UDMA_CRC_Error_Count    -OSRCK   198   198   000    -    15
240 Head_Flying_Hours       ------   100   253   000    -    15855h+17m+56.122s
241 Total_LBAs_Written      ------   100   253   000    -    150830844071993
242 Total_LBAs_Read         ------   100   253   000    -    281269763427819
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      5  Comprehensive SMART error log
0x03       GPL     R/O      5  Ext. Comprehensive SMART error log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      1  Extended self-test log
0x09           SL  R/W      1  Selective self-test log
0x10       GPL     R/O      1  NCQ Command Error log
0x11       GPL     R/O      1  SATA Phy Event Counters
0x21       GPL     R/O      1  Write stream error log
0x22       GPL     R/O      1  Read stream error log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xa1       GPL,SL  VS      20  Device vendor specific log
0xa2       GPL     VS    4496  Device vendor specific log
0xa8       GPL,SL  VS      20  Device vendor specific log
0xa9       GPL,SL  VS       1  Device vendor specific log
0xab       GPL     VS       1  Device vendor specific log
0xb0       GPL     VS    5067  Device vendor specific log
0xbd       GPL     VS     512  Device vendor specific log
0xbe-0xbf  GPL     VS   65535  Device vendor specific log
0xc0       GPL,SL  VS       1  Device vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (5 sectors)
No Errors Logged

SMART Extended Self-test Log Version: 1 (1 sectors)
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%     13549         -
# 2  Short offline       Completed without error       00%     13525         -
# 3  Extended offline    Completed without error       00%     13507         -
# 4  Short offline       Completed without error       00%     13501         -
# 5  Short offline       Completed without error       00%     13477         -
# 6  Short offline       Completed without error       00%     13453         -
# 7  Short offline       Completed without error       00%     13429         -
# 8  Short offline       Completed without error       00%     13405         -
# 9  Short offline       Completed without error       00%     13381         -
#10  Short offline       Completed without error       00%     13357         -
#11  Extended offline    Completed without error       00%     13339         -
#12  Short offline       Completed without error       00%     13333         -
#13  Short offline       Completed without error       00%     13309         -
#14  Short offline       Completed without error       00%     13285         -
#15  Short offline       Completed without error       00%     13261         -
#16  Short offline       Completed without error       00%     13237         -
#17  Extended offline    Interrupted (host reset)      70%     13220         -
#18  Short offline       Completed without error       00%     13165         -
#19  Short offline       Completed without error       00%     13141         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  3
SCT Version (vendor specific):       522 (0x020a)
SCT Support Level:                   1
Device State:                        Active (0)
Current Temperature:                    23 Celsius
Power Cycle Min/Max Temperature:     23/24 Celsius
Lifetime    Min/Max Temperature:     20/33 Celsius
Under/Over Temperature Limit Count:   0/0

SCT Data Table command not supported

SCT Error Recovery Control command not supported

Device Statistics (GP Log 0x04) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x000a  2            4  Device-to-host register FISes sent due to a COMRESET
0x0001  2            5  Command failed due to ICRC error
0x0003  2            5  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS

/dev/da13
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p10 amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               SEAGATE
Product:              ST3000NM0023
Revision:             0004
Compliance:           SPC-4
User Capacity:        3,000,592,982,016 bytes [3.00 TB]
Logical block size:   512 bytes
LB provisioning type: unreported, LBPME=0, LBPRZ=0
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000c500591e0173
Serial number:        Z1Z4VV280000W501HA5Y
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Wed Mar 25 09:49:02 2015 CET
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     31 C
Drive Trip Temperature:        60 C

Manufactured in week 30 of year 2014
Specified cycle count over device lifetime:  10000
Accumulated start-stop cycles:  106
Specified load-unload count over device lifetime:  300000
Accumulated load-unload cycles:  205
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 1422243687
  Blocks received from initiator = 2621986399
  Blocks read from cache and sent to initiator = 1032188814
  Number of read and write commands whose size <= segment size = 9802728
  Number of read and write commands whose size > segment size = 6036

Vendor (Seagate/Hitachi) factory information
  number of hours powered up = 2549.17
  number of minutes until next internal SMART test = 17

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:   567900894        0         0  567900894          0       2927.212           0
write:         0        0         0         0          0       2029.374           0

Non-medium error count:        2


[GLTSD (Global Logging Target Save Disable) set. Enable Save with '-S on']
SMART Self-test log
Num  Test              Status                 segment  LifeTime  LBA_first_err [SK ASC ASQ]
     Description                              number   (hours)
# 1  Background short  Completed                   -    2539                 - [-   -    -]
# 2  Background short  Completed                   -    2527                 - [-   -    -]
# 3  Background short  Completed                   -    2515                 - [-   -    -]
# 4  Background short  Completed                   -    2503                 - [-   -    -]
# 5  Background short  Completed                   -    2491                 - [-   -    -]
# 6  Background short  Completed                   -    2479                 - [-   -    -]
# 7  Background short  Completed                   -    2467                 - [-   -    -]
# 8  Background short  Completed                   -    2455                 - [-   -    -]
# 9  Background short  Completed                   -    2443                 - [-   -    -]
#10  Background short  Completed                   -    2431                 - [-   -    -]
#11  Background short  Completed                   -    2419                 - [-   -    -]
#12  Background short  Completed                   -    2407                 - [-   -    -]
#13  Background short  Completed                   -    2395                 - [-   -    -]
#14  Background short  Completed                   -    2383                 - [-   -    -]
#15  Background short  Completed                   -    2371                 - [-   -    -]
#16  Background short  Completed                   -    2359                 - [-   -    -]
#17  Background short  Completed                   -    2347                 - [-   -    -]
#18  Background short  Completed                   -    2335                 - [-   -    -]
#19  Background short  Completed                   -    2323                 - [-   -    -]
#20  Background short  Completed                   -    2311                 - [-   -    -]

Long (extended) Self Test duration: 26000 seconds [433.3 minutes]

Background scan results log
  Status: waiting until BMS interval timer expires
    Accumulated power on time, hours:minutes 2549:10 [152950 minutes]
    Number of background scans performed: 32,  scan progress: 0.00%
    Number of background medium scans performed: 32

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 2
  number of phys = 1
  phy identifier = 0
    attached device type: SAS or SATA device
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; 6 Gbps
    attached initiator port: ssp=1 stp=1 smp=1
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c500591e0171
    attached SAS address = 0x500605b009954166
    attached phy identifier = 7
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 9214
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 9214
     Phy reset problem count: 0
relative target port id = 2
  generation code = 2
  number of phys = 1
  phy identifier = 1
    attached device type: no device attached
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; unknown
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c500591e0172
    attached SAS address = 0x0
    attached phy identifier = 0
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da12
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p10 amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               SEAGATE
Product:              ST3000NM0023
Revision:             0004
Compliance:           SPC-4
User Capacity:        3,000,592,982,016 bytes [3.00 TB]
Logical block size:   512 bytes
LB provisioning type: unreported, LBPME=0, LBPRZ=0
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000c500591d0d3b
Serial number:        Z1Z53Z480000W501ZEFA
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Wed Mar 25 09:49:03 2015 CET
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     30 C
Drive Trip Temperature:        60 C

Manufactured in week 30 of year 2014
Specified cycle count over device lifetime:  10000
Accumulated start-stop cycles:  106
Specified load-unload count over device lifetime:  300000
Accumulated load-unload cycles:  205
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 1414502341
  Blocks received from initiator = 2768641386
  Blocks read from cache and sent to initiator = 1028601493
  Number of read and write commands whose size <= segment size = 9788378
  Number of read and write commands whose size > segment size = 6010

Vendor (Seagate/Hitachi) factory information
  number of hours powered up = 2549.18
  number of minutes until next internal SMART test = 17

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:   1738771192        0         0  1738771192          0       2923.248           0
write:         0        0         0         0          0       2065.463           0

Non-medium error count:        2


[GLTSD (Global Logging Target Save Disable) set. Enable Save with '-S on']
SMART Self-test log
Num  Test              Status                 segment  LifeTime  LBA_first_err [SK ASC ASQ]
     Description                              number   (hours)
# 1  Background short  Completed                   -    2539                 - [-   -    -]
# 2  Background short  Completed                   -    2527                 - [-   -    -]
# 3  Background short  Completed                   -    2515                 - [-   -    -]
# 4  Background short  Completed                   -    2503                 - [-   -    -]
# 5  Background short  Completed                   -    2491                 - [-   -    -]
# 6  Background short  Completed                   -    2479                 - [-   -    -]
# 7  Background short  Completed                   -    2467                 - [-   -    -]
# 8  Background short  Completed                   -    2455                 - [-   -    -]
# 9  Background short  Completed                   -    2443                 - [-   -    -]
#10  Background short  Completed                   -    2431                 - [-   -    -]
#11  Background short  Completed                   -    2419                 - [-   -    -]
#12  Background short  Completed                   -    2407                 - [-   -    -]
#13  Background short  Completed                   -    2395                 - [-   -    -]
#14  Background short  Completed                   -    2383                 - [-   -    -]
#15  Background short  Completed                   -    2371                 - [-   -    -]
#16  Background short  Completed                   -    2359                 - [-   -    -]
#17  Background short  Completed                   -    2347                 - [-   -    -]
#18  Background short  Completed                   -    2335                 - [-   -    -]
#19  Background short  Completed                   -    2323                 - [-   -    -]
#20  Background short  Completed                   -    2311                 - [-   -    -]

Long (extended) Self Test duration: 26000 seconds [433.3 minutes]

Background scan results log
  Status: waiting until BMS interval timer expires
    Accumulated power on time, hours:minutes 2549:11 [152951 minutes]
    Number of background scans performed: 32,  scan progress: 0.00%
    Number of background medium scans performed: 32

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 2
  number of phys = 1
  phy identifier = 0
    attached device type: SAS or SATA device
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; 6 Gbps
    attached initiator port: ssp=1 stp=1 smp=1
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c500591d0d39
    attached SAS address = 0x500605b009954165
    attached phy identifier = 6
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 8642
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 8642
     Phy reset problem count: 0
relative target port id = 2
  generation code = 2
  number of phys = 1
  phy identifier = 1
    attached device type: no device attached
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; unknown
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c500591d0d3a
    attached SAS address = 0x0
    attached phy identifier = 0
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da11
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p10 amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               SEAGATE
Product:              ST3000NM0023
Revision:             0004
Compliance:           SPC-4
User Capacity:        3,000,592,982,016 bytes [3.00 TB]
Logical block size:   512 bytes
LB provisioning type: unreported, LBPME=0, LBPRZ=0
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000c5005911060f
Serial number:        Z1Y20KJ70000W4501HGL
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Wed Mar 25 09:49:04 2015 CET
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     28 C
Drive Trip Temperature:        60 C

Manufactured in week 30 of year 2014
Specified cycle count over device lifetime:  10000
Accumulated start-stop cycles:  199
Specified load-unload count over device lifetime:  300000
Accumulated load-unload cycles:  298
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 1425357128
  Blocks received from initiator = 2725556839
  Blocks read from cache and sent to initiator = 1036240621
  Number of read and write commands whose size <= segment size = 9791339
  Number of read and write commands whose size > segment size = 5904

Vendor (Seagate/Hitachi) factory information
  number of hours powered up = 2549.17
  number of minutes until next internal SMART test = 17

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:   3159443501        0         0  3159443501          0       2928.806           0
write:         0        0         0         0          0       2113.899           0

Non-medium error count:        6


[GLTSD (Global Logging Target Save Disable) set. Enable Save with '-S on']
SMART Self-test log
Num  Test              Status                 segment  LifeTime  LBA_first_err [SK ASC ASQ]
     Description                              number   (hours)
# 1  Background short  Completed                   -    2539                 - [-   -    -]
# 2  Background short  Completed                   -    2527                 - [-   -    -]
# 3  Background short  Completed                   -    2515                 - [-   -    -]
# 4  Background short  Completed                   -    2503                 - [-   -    -]
# 5  Background short  Completed                   -    2491                 - [-   -    -]
# 6  Background short  Completed                   -    2479                 - [-   -    -]
# 7  Background short  Completed                   -    2467                 - [-   -    -]
# 8  Background short  Completed                   -    2455                 - [-   -    -]
# 9  Background short  Completed                   -    2443                 - [-   -    -]
#10  Background short  Completed                   -    2431                 - [-   -    -]
#11  Background short  Completed                   -    2419                 - [-   -    -]
#12  Background short  Completed                   -    2407                 - [-   -    -]
#13  Background short  Completed                   -    2395                 - [-   -    -]
#14  Background short  Completed                   -    2383                 - [-   -    -]
#15  Background short  Completed                   -    2371                 - [-   -    -]
#16  Background short  Completed                   -    2359                 - [-   -    -]
#17  Background short  Completed                   -    2347                 - [-   -    -]
#18  Background short  Completed                   -    2335                 - [-   -    -]
#19  Background short  Completed                   -    2323                 - [-   -    -]
#20  Background short  Completed                   -    2311                 - [-   -    -]

Long (extended) Self Test duration: 26000 seconds [433.3 minutes]

Background scan results log
  Status: waiting until BMS interval timer expires
    Accumulated power on time, hours:minutes 2549:10 [152950 minutes]
    Number of background scans performed: 32,  scan progress: 0.00%
    Number of background medium scans performed: 32

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 2
  number of phys = 1
  phy identifier = 0
    attached device type: SAS or SATA device
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; 6 Gbps
    attached initiator port: ssp=1 stp=1 smp=1
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c5005911060d
    attached SAS address = 0x500605b009954164
    attached phy identifier = 3
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 2
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 2
     Phy reset problem count: 0
relative target port id = 2
  generation code = 2
  number of phys = 1
  phy identifier = 1
    attached device type: no device attached
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; unknown
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c5005911060e
    attached SAS address = 0x0
    attached phy identifier = 0
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da10
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p10 amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               SEAGATE
Product:              ST3000NM0023
Revision:             0004
Compliance:           SPC-4
User Capacity:        3,000,592,982,016 bytes [3.00 TB]
Logical block size:   512 bytes
LB provisioning type: unreported, LBPME=0, LBPRZ=0
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000c5005910f553
Serial number:        Z1Y20KSJ0000C501C1EZ
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Wed Mar 25 09:49:05 2015 CET
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     28 C
Drive Trip Temperature:        60 C

Manufactured in week 30 of year 2014
Specified cycle count over device lifetime:  10000
Accumulated start-stop cycles:  199
Specified load-unload count over device lifetime:  300000
Accumulated load-unload cycles:  297
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 1419716910
  Blocks received from initiator = 2622224370
  Blocks read from cache and sent to initiator = 1030932874
  Number of read and write commands whose size <= segment size = 9803503
  Number of read and write commands whose size > segment size = 6124

Vendor (Seagate/Hitachi) factory information
  number of hours powered up = 2549.15
  number of minutes until next internal SMART test = 17

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:   3398739411        0         0  3398739411          0       2925.918           0
write:         0        0         0         0          0       2423.246           0

Non-medium error count:        2


[GLTSD (Global Logging Target Save Disable) set. Enable Save with '-S on']
SMART Self-test log
Num  Test              Status                 segment  LifeTime  LBA_first_err [SK ASC ASQ]
     Description                              number   (hours)
# 1  Background short  Completed                   -    2539                 - [-   -    -]
# 2  Background short  Completed                   -    2527                 - [-   -    -]
# 3  Background short  Completed                   -    2515                 - [-   -    -]
# 4  Background short  Completed                   -    2503                 - [-   -    -]
# 5  Background short  Completed                   -    2491                 - [-   -    -]
# 6  Background short  Completed                   -    2479                 - [-   -    -]
# 7  Background short  Completed                   -    2467                 - [-   -    -]
# 8  Background short  Completed                   -    2455                 - [-   -    -]
# 9  Background short  Completed                   -    2443                 - [-   -    -]
#10  Background short  Completed                   -    2431                 - [-   -    -]
#11  Background short  Completed                   -    2419                 - [-   -    -]
#12  Background short  Completed                   -    2407                 - [-   -    -]
#13  Background short  Completed                   -    2395                 - [-   -    -]
#14  Background short  Completed                   -    2383                 - [-   -    -]
#15  Background short  Completed                   -    2371                 - [-   -    -]
#16  Background short  Completed                   -    2359                 - [-   -    -]
#17  Background short  Completed                   -    2347                 - [-   -    -]
#18  Background short  Completed                   -    2335                 - [-   -    -]
#19  Background short  Completed                   -    2323                 - [-   -    -]
#20  Background short  Completed                   -    2311                 - [-   -    -]

Long (extended) Self Test duration: 26000 seconds [433.3 minutes]

Background scan results log
  Status: waiting until BMS interval timer expires
    Accumulated power on time, hours:minutes 2549:09 [152949 minutes]
    Number of background scans performed: 32,  scan progress: 0.00%
    Number of background medium scans performed: 32

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 2
  number of phys = 1
  phy identifier = 0
    attached device type: SAS or SATA device
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; 6 Gbps
    attached initiator port: ssp=1 stp=1 smp=1
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c5005910f551
    attached SAS address = 0x500605b009954163
    attached phy identifier = 2
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 2
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 2
     Phy reset problem count: 0
relative target port id = 2
  generation code = 2
  number of phys = 1
  phy identifier = 1
    attached device type: no device attached
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; unknown
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c5005910f552
    attached SAS address = 0x0
    attached phy identifier = 0
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da9
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p10 amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               SEAGATE
Product:              ST3000NM0023
Revision:             0004
Compliance:           SPC-4
User Capacity:        3,000,592,982,016 bytes [3.00 TB]
Logical block size:   512 bytes
LB provisioning type: unreported, LBPME=0, LBPRZ=0
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000c500591e000b
Serial number:        Z1Z51L4Y0000W5019F3Q
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Wed Mar 25 09:49:06 2015 CET
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     28 C
Drive Trip Temperature:        60 C

Manufactured in week 30 of year 2014
Specified cycle count over device lifetime:  10000
Accumulated start-stop cycles:  106
Specified load-unload count over device lifetime:  300000
Accumulated load-unload cycles:  205
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 1412729408
  Blocks received from initiator = 2621998658
  Blocks read from cache and sent to initiator = 1032090945
  Number of read and write commands whose size <= segment size = 9803845
  Number of read and write commands whose size > segment size = 6251

Vendor (Seagate/Hitachi) factory information
  number of hours powered up = 2549.32
  number of minutes until next internal SMART test = 17

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:   380989232        0         0  380989232          0       2922.341           0
write:         0        0         0         0          0       2231.376           0

Non-medium error count:        2


[GLTSD (Global Logging Target Save Disable) set. Enable Save with '-S on']
SMART Self-test log
Num  Test              Status                 segment  LifeTime  LBA_first_err [SK ASC ASQ]
     Description                              number   (hours)
# 1  Background short  Completed                   -    2540                 - [-   -    -]
# 2  Background short  Completed                   -    2528                 - [-   -    -]
# 3  Background short  Completed                   -    2516                 - [-   -    -]
# 4  Background short  Completed                   -    2503                 - [-   -    -]
# 5  Background short  Completed                   -    2491                 - [-   -    -]
# 6  Background short  Completed                   -    2479                 - [-   -    -]
# 7  Background short  Completed                   -    2467                 - [-   -    -]
# 8  Background short  Completed                   -    2455                 - [-   -    -]
# 9  Background short  Completed                   -    2443                 - [-   -    -]
#10  Background short  Completed                   -    2431                 - [-   -    -]
#11  Background short  Completed                   -    2419                 - [-   -    -]
#12  Background short  Completed                   -    2407                 - [-   -    -]
#13  Background short  Completed                   -    2395                 - [-   -    -]
#14  Background short  Completed                   -    2383                 - [-   -    -]
#15  Background short  Completed                   -    2371                 - [-   -    -]
#16  Background short  Completed                   -    2359                 - [-   -    -]
#17  Background short  Completed                   -    2347                 - [-   -    -]
#18  Background short  Completed                   -    2335                 - [-   -    -]
#19  Background short  Completed                   -    2323                 - [-   -    -]
#20  Background short  Completed                   -    2311                 - [-   -    -]

Long (extended) Self Test duration: 26000 seconds [433.3 minutes]

Background scan results log
  Status: waiting until BMS interval timer expires
    Accumulated power on time, hours:minutes 2549:19 [152959 minutes]
    Number of background scans performed: 32,  scan progress: 0.00%
    Number of background medium scans performed: 32

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 2
  number of phys = 1
  phy identifier = 0
    attached device type: SAS or SATA device
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; 6 Gbps
    attached initiator port: ssp=1 stp=1 smp=1
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c500591e0009
    attached SAS address = 0x500605b009954162
    attached phy identifier = 1
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 8434
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 8434
     Phy reset problem count: 0
relative target port id = 2
  generation code = 2
  number of phys = 1
  phy identifier = 1
    attached device type: no device attached
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; unknown
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c500591e000a
    attached SAS address = 0x0
    attached phy identifier = 0
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da8
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p10 amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               SEAGATE
Product:              ST3000NM0023
Revision:             0004
Compliance:           SPC-4
User Capacity:        3,000,592,982,016 bytes [3.00 TB]
Logical block size:   512 bytes
LB provisioning type: unreported, LBPME=0, LBPRZ=0
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000c500591e0a57
Serial number:        Z1Z50LCF0000W5018F5M
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Wed Mar 25 09:49:07 2015 CET
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     27 C
Drive Trip Temperature:        60 C

Manufactured in week 30 of year 2014
Specified cycle count over device lifetime:  10000
Accumulated start-stop cycles:  106
Specified load-unload count over device lifetime:  300000
Accumulated load-unload cycles:  205
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 1418650220
  Blocks received from initiator = 2621691187
  Blocks read from cache and sent to initiator = 1035338087
  Number of read and write commands whose size <= segment size = 9800529
  Number of read and write commands whose size > segment size = 6142

Vendor (Seagate/Hitachi) factory information
  number of hours powered up = 2549.15
  number of minutes until next internal SMART test = 17

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:   862445636        0         0  862445636          0       2925.372           0
write:         0        0         0         0          0       2184.377           0

Non-medium error count:        2


[GLTSD (Global Logging Target Save Disable) set. Enable Save with '-S on']
SMART Self-test log
Num  Test              Status                 segment  LifeTime  LBA_first_err [SK ASC ASQ]
     Description                              number   (hours)
# 1  Background short  Completed                   -    2539                 - [-   -    -]
# 2  Background short  Completed                   -    2527                 - [-   -    -]
# 3  Background short  Completed                   -    2515                 - [-   -    -]
# 4  Background short  Completed                   -    2503                 - [-   -    -]
# 5  Background short  Completed                   -    2491                 - [-   -    -]
# 6  Background short  Completed                   -    2479                 - [-   -    -]
# 7  Background short  Completed                   -    2467                 - [-   -    -]
# 8  Background short  Completed                   -    2455                 - [-   -    -]
# 9  Background short  Completed                   -    2443                 - [-   -    -]
#10  Background short  Completed                   -    2431                 - [-   -    -]
#11  Background short  Completed                   -    2419                 - [-   -    -]
#12  Background short  Completed                   -    2407                 - [-   -    -]
#13  Background short  Completed                   -    2395                 - [-   -    -]
#14  Background short  Completed                   -    2383                 - [-   -    -]
#15  Background short  Completed                   -    2371                 - [-   -    -]
#16  Background short  Completed                   -    2359                 - [-   -    -]
#17  Background short  Completed                   -    2347                 - [-   -    -]
#18  Background short  Completed                   -    2335                 - [-   -    -]
#19  Background short  Completed                   -    2323                 - [-   -    -]
#20  Background short  Completed                   -    2311                 - [-   -    -]

Long (extended) Self Test duration: 26000 seconds [433.3 minutes]

Background scan results log
  Status: waiting until BMS interval timer expires
    Accumulated power on time, hours:minutes 2549:09 [152949 minutes]
    Number of background scans performed: 32,  scan progress: 0.00%
    Number of background medium scans performed: 32

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 0
  number of phys = 1
  phy identifier = 0
    attached device type: SAS or SATA device
    attached reason: power on
    reason: loss of dword synchronization
    negotiated logical link rate: phy enabled; 6 Gbps
    attached initiator port: ssp=1 stp=1 smp=1
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c500591e0a55
    attached SAS address = 0x500605b009954160
    attached phy identifier = 0
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 2
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 2
     Phy reset problem count: 0
relative target port id = 2
  generation code = 0
  number of phys = 1
  phy identifier = 1
    attached device type: no device attached
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; unknown
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c500591e0a56
    attached SAS address = 0x0
    attached phy identifier = 0
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da7
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p10 amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               SEAGATE
Product:              ST3000NM0023
Revision:             0004
Compliance:           SPC-4
User Capacity:        3,000,592,982,016 bytes [3.00 TB]
Logical block size:   512 bytes
LB provisioning type: unreported, LBPME=0, LBPRZ=0
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000c5005910ec4f
Serial number:        Z1Y20KYX0000C501C406
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Wed Mar 25 09:49:08 2015 CET
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     29 C
Drive Trip Temperature:        60 C

Manufactured in week 30 of year 2014
Specified cycle count over device lifetime:  10000
Accumulated start-stop cycles:  260
Specified load-unload count over device lifetime:  300000
Accumulated load-unload cycles:  359
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 1420544928
  Blocks received from initiator = 2873642480
  Blocks read from cache and sent to initiator = 1032051617
  Number of read and write commands whose size <= segment size = 9784317
  Number of read and write commands whose size > segment size = 6113

Vendor (Seagate/Hitachi) factory information
  number of hours powered up = 2549.22
  number of minutes until next internal SMART test = 17

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:   2461654730        0         0  2461654730          0       2926.342           0
write:         0        0         0         0          0       2573.060           0

Non-medium error count:        1


[GLTSD (Global Logging Target Save Disable) set. Enable Save with '-S on']
SMART Self-test log
Num  Test              Status                 segment  LifeTime  LBA_first_err [SK ASC ASQ]
     Description                              number   (hours)
# 1  Background short  Completed                   -    2539                 - [-   -    -]
# 2  Background short  Completed                   -    2527                 - [-   -    -]
# 3  Background short  Completed                   -    2515                 - [-   -    -]
# 4  Background short  Completed                   -    2503                 - [-   -    -]
# 5  Background short  Completed                   -    2491                 - [-   -    -]
# 6  Background short  Completed                   -    2479                 - [-   -    -]
# 7  Background short  Completed                   -    2467                 - [-   -    -]
# 8  Background short  Completed                   -    2455                 - [-   -    -]
# 9  Background short  Completed                   -    2443                 - [-   -    -]
#10  Background short  Completed                   -    2431                 - [-   -    -]
#11  Background short  Completed                   -    2419                 - [-   -    -]
#12  Background short  Completed                   -    2407                 - [-   -    -]
#13  Background short  Completed                   -    2395                 - [-   -    -]
#14  Background short  Completed                   -    2383                 - [-   -    -]
#15  Background short  Completed                   -    2371                 - [-   -    -]
#16  Background short  Completed                   -    2359                 - [-   -    -]
#17  Background short  Completed                   -    2347                 - [-   -    -]
#18  Background short  Completed                   -    2335                 - [-   -    -]
#19  Background short  Completed                   -    2323                 - [-   -    -]
#20  Background short  Completed                   -    2311                 - [-   -    -]

Long (extended) Self Test duration: 26000 seconds [433.3 minutes]

Background scan results log
  Status: waiting until BMS interval timer expires
    Accumulated power on time, hours:minutes 2549:13 [152953 minutes]
    Number of background scans performed: 32,  scan progress: 0.00%
    Number of background medium scans performed: 32

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 2
  number of phys = 1
  phy identifier = 0
    attached device type: SAS or SATA device
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; 6 Gbps
    attached initiator port: ssp=1 stp=1 smp=1
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c5005910ec4d
    attached SAS address = 0x50030480194d7d03
    attached phy identifier = 3
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 2
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 2
     Phy reset problem count: 0
relative target port id = 2
  generation code = 2
  number of phys = 1
  phy identifier = 1
    attached device type: no device attached
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; unknown
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c5005910ec4e
    attached SAS address = 0x0
    attached phy identifier = 0
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da6
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p10 amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               SEAGATE
Product:              ST3000NM0023
Revision:             0004
Compliance:           SPC-4
User Capacity:        3,000,592,982,016 bytes [3.00 TB]
Logical block size:   512 bytes
LB provisioning type: unreported, LBPME=0, LBPRZ=0
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000c50058f2ef8b
Serial number:        Z1Y1XL7B0000C450BQJS
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Wed Mar 25 09:49:09 2015 CET
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     28 C
Drive Trip Temperature:        60 C

Manufactured in week 30 of year 2014
Specified cycle count over device lifetime:  10000
Accumulated start-stop cycles:  265
Specified load-unload count over device lifetime:  300000
Accumulated load-unload cycles:  560
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 1429004913
  Blocks received from initiator = 2770334028
  Blocks read from cache and sent to initiator = 1037618622
  Number of read and write commands whose size <= segment size = 9798970
  Number of read and write commands whose size > segment size = 6094

Vendor (Seagate/Hitachi) factory information
  number of hours powered up = 2549.13
  number of minutes until next internal SMART test = 17

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:   337645424        0         0  337645424          0       2930.675           0
write:         0        0         0         0          0       2290.145           0

Non-medium error count:        0


[GLTSD (Global Logging Target Save Disable) set. Enable Save with '-S on']
SMART Self-test log
Num  Test              Status                 segment  LifeTime  LBA_first_err [SK ASC ASQ]
     Description                              number   (hours)
# 1  Background short  Completed                   -    2539                 - [-   -    -]
# 2  Background short  Completed                   -    2527                 - [-   -    -]
# 3  Background short  Completed                   -    2515                 - [-   -    -]
# 4  Background short  Completed                   -    2503                 - [-   -    -]
# 5  Background short  Completed                   -    2491                 - [-   -    -]
# 6  Background short  Completed                   -    2479                 - [-   -    -]
# 7  Background short  Completed                   -    2467                 - [-   -    -]
# 8  Background short  Completed                   -    2455                 - [-   -    -]
# 9  Background short  Completed                   -    2443                 - [-   -    -]
#10  Background short  Completed                   -    2431                 - [-   -    -]
#11  Background short  Completed                   -    2419                 - [-   -    -]
#12  Background short  Completed                   -    2407                 - [-   -    -]
#13  Background short  Completed                   -    2395                 - [-   -    -]
#14  Background short  Completed                   -    2383                 - [-   -    -]
#15  Background short  Completed                   -    2371                 - [-   -    -]
#16  Background short  Completed                   -    2359                 - [-   -    -]
#17  Background short  Completed                   -    2347                 - [-   -    -]
#18  Background short  Completed                   -    2335                 - [-   -    -]
#19  Background short  Completed                   -    2323                 - [-   -    -]
#20  Background short  Completed                   -    2311                 - [-   -    -]

Long (extended) Self Test duration: 26000 seconds [433.3 minutes]

Background scan results log
  Status: waiting until BMS interval timer expires
    Accumulated power on time, hours:minutes 2549:08 [152948 minutes]
    Number of background scans performed: 32,  scan progress: 0.00%
    Number of background medium scans performed: 32

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 2
  number of phys = 1
  phy identifier = 0
    attached device type: SAS or SATA device
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; 6 Gbps
    attached initiator port: ssp=1 stp=1 smp=1
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c50058f2ef89
    attached SAS address = 0x50030480194d7d02
    attached phy identifier = 2
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 9517
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 9517
     Phy reset problem count: 0
relative target port id = 2
  generation code = 2
  number of phys = 1
  phy identifier = 1
    attached device type: no device attached
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; unknown
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c50058f2ef8a
    attached SAS address = 0x0
    attached phy identifier = 0
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da5
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p10 amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               SEAGATE
Product:              ST3000NM0023
Revision:             0004
Compliance:           SPC-4
User Capacity:        3,000,592,982,016 bytes [3.00 TB]
Logical block size:   512 bytes
LB provisioning type: unreported, LBPME=0, LBPRZ=0
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000c5005910f66f
Serial number:        Z1Y204W10000W45122TV
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Wed Mar 25 09:49:10 2015 CET
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     28 C
Drive Trip Temperature:        60 C

Manufactured in week 30 of year 2014
Specified cycle count over device lifetime:  10000
Accumulated start-stop cycles:  199
Specified load-unload count over device lifetime:  300000
Accumulated load-unload cycles:  298
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 1424828871
  Blocks received from initiator = 2636390910
  Blocks read from cache and sent to initiator = 1038411953
  Number of read and write commands whose size <= segment size = 9802774
  Number of read and write commands whose size > segment size = 5880

Vendor (Seagate/Hitachi) factory information
  number of hours powered up = 2549.20
  number of minutes until next internal SMART test = 17

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:   2485778728        0         0  2485778728          0       2928.536           0
write:         0        0         0         0          0       2227.364           0

Non-medium error count:        0


[GLTSD (Global Logging Target Save Disable) set. Enable Save with '-S on']
SMART Self-test log
Num  Test              Status                 segment  LifeTime  LBA_first_err [SK ASC ASQ]
     Description                              number   (hours)
# 1  Background short  Completed                   -    2539                 - [-   -    -]
# 2  Background short  Completed                   -    2527                 - [-   -    -]
# 3  Background short  Completed                   -    2515                 - [-   -    -]
# 4  Background short  Completed                   -    2503                 - [-   -    -]
# 5  Background short  Completed                   -    2491                 - [-   -    -]
# 6  Background short  Completed                   -    2479                 - [-   -    -]
# 7  Background short  Completed                   -    2467                 - [-   -    -]
# 8  Background short  Completed                   -    2455                 - [-   -    -]
# 9  Background short  Completed                   -    2443                 - [-   -    -]
#10  Background short  Completed                   -    2431                 - [-   -    -]
#11  Background short  Completed                   -    2419                 - [-   -    -]
#12  Background short  Completed                   -    2407                 - [-   -    -]
#13  Background short  Completed                   -    2395                 - [-   -    -]
#14  Background short  Completed                   -    2383                 - [-   -    -]
#15  Background short  Completed                   -    2371                 - [-   -    -]
#16  Background short  Completed                   -    2359                 - [-   -    -]
#17  Background short  Completed                   -    2347                 - [-   -    -]
#18  Background short  Completed                   -    2335                 - [-   -    -]
#19  Background short  Completed                   -    2323                 - [-   -    -]
#20  Background short  Completed                   -    2311                 - [-   -    -]

Long (extended) Self Test duration: 26000 seconds [433.3 minutes]

Background scan results log
  Status: waiting until BMS interval timer expires
    Accumulated power on time, hours:minutes 2549:12 [152952 minutes]
    Number of background scans performed: 32,  scan progress: 0.00%
    Number of background medium scans performed: 32

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 2
  number of phys = 1
  phy identifier = 0
    attached device type: SAS or SATA device
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; 6 Gbps
    attached initiator port: ssp=1 stp=1 smp=1
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c5005910f66d
    attached SAS address = 0x50030480194d7d07
    attached phy identifier = 7
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 2
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 2
     Phy reset problem count: 0
relative target port id = 2
  generation code = 2
  number of phys = 1
  phy identifier = 1
    attached device type: no device attached
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; unknown
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c5005910f66e
    attached SAS address = 0x0
    attached phy identifier = 0
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da4
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p10 amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               SEAGATE
Product:              ST3000NM0023
Revision:             0004
Compliance:           SPC-4
User Capacity:        3,000,592,982,016 bytes [3.00 TB]
Logical block size:   512 bytes
LB provisioning type: unreported, LBPME=0, LBPRZ=0
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000c50059110c73
Serial number:        Z1Y20KFN0000W4511X3Q
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Wed Mar 25 09:49:11 2015 CET
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     26 C
Drive Trip Temperature:        60 C

Manufactured in week 30 of year 2014
Specified cycle count over device lifetime:  10000
Accumulated start-stop cycles:  199
Specified load-unload count over device lifetime:  300000
Accumulated load-unload cycles:  298
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 1427655674
  Blocks received from initiator = 2621154730
  Blocks read from cache and sent to initiator = 1041766732
  Number of read and write commands whose size <= segment size = 9809267
  Number of read and write commands whose size > segment size = 6314

Vendor (Seagate/Hitachi) factory information
  number of hours powered up = 2549.18
  number of minutes until next internal SMART test = 17

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:   173395605        0         0  173395605          0       2929.983           0
write:         0        0         0         0          0       2391.662           0

Non-medium error count:        2


[GLTSD (Global Logging Target Save Disable) set. Enable Save with '-S on']
SMART Self-test log
Num  Test              Status                 segment  LifeTime  LBA_first_err [SK ASC ASQ]
     Description                              number   (hours)
# 1  Background short  Completed                   -    2539                 - [-   -    -]
# 2  Background short  Completed                   -    2527                 - [-   -    -]
# 3  Background short  Completed                   -    2515                 - [-   -    -]
# 4  Background short  Completed                   -    2503                 - [-   -    -]
# 5  Background short  Completed                   -    2491                 - [-   -    -]
# 6  Background short  Completed                   -    2479                 - [-   -    -]
# 7  Background short  Completed                   -    2467                 - [-   -    -]
# 8  Background short  Completed                   -    2455                 - [-   -    -]
# 9  Background short  Completed                   -    2443                 - [-   -    -]
#10  Background short  Completed                   -    2431                 - [-   -    -]
#11  Background short  Completed                   -    2419                 - [-   -    -]
#12  Background short  Completed                   -    2407                 - [-   -    -]
#13  Background short  Completed                   -    2395                 - [-   -    -]
#14  Background short  Completed                   -    2383                 - [-   -    -]
#15  Background short  Completed                   -    2371                 - [-   -    -]
#16  Background short  Completed                   -    2359                 - [-   -    -]
#17  Background short  Completed                   -    2347                 - [-   -    -]
#18  Background short  Completed                   -    2335                 - [-   -    -]
#19  Background short  Completed                   -    2323                 - [-   -    -]
#20  Background short  Completed                   -    2311                 - [-   -    -]

Long (extended) Self Test duration: 26000 seconds [433.3 minutes]

Background scan results log
  Status: waiting until BMS interval timer expires
    Accumulated power on time, hours:minutes 2549:11 [152951 minutes]
    Number of background scans performed: 32,  scan progress: 0.00%
    Number of background medium scans performed: 32

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 2
  number of phys = 1
  phy identifier = 0
    attached device type: SAS or SATA device
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; 6 Gbps
    attached initiator port: ssp=1 stp=1 smp=1
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c50059110c71
    attached SAS address = 0x50030480194d7d06
    attached phy identifier = 6
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 3
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 3
     Phy reset problem count: 0
relative target port id = 2
  generation code = 2
  number of phys = 1
  phy identifier = 1
    attached device type: no device attached
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; unknown
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c50059110c72
    attached SAS address = 0x0
    attached phy identifier = 0
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da3
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p10 amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               SEAGATE
Product:              ST3000NM0023
Revision:             0004
Compliance:           SPC-4
User Capacity:        3,000,592,982,016 bytes [3.00 TB]
Logical block size:   512 bytes
LB provisioning type: unreported, LBPME=0, LBPRZ=0
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000c5005910e5fb
Serial number:        Z1Y205470000W45122VF
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Wed Mar 25 09:49:12 2015 CET
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     30 C
Drive Trip Temperature:        60 C

Manufactured in week 30 of year 2014
Specified cycle count over device lifetime:  10000
Accumulated start-stop cycles:  247
Specified load-unload count over device lifetime:  300000
Accumulated load-unload cycles:  346
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 1427024234
  Blocks received from initiator = 2874545496
  Blocks read from cache and sent to initiator = 1036838159
  Number of read and write commands whose size <= segment size = 9796878
  Number of read and write commands whose size > segment size = 6074

Vendor (Seagate/Hitachi) factory information
  number of hours powered up = 2549.20
  number of minutes until next internal SMART test = 17

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:   2792546354        0         0  2792546354          0       2929.660           0
write:         0        0         0         0          0       2357.443           0

Non-medium error count:        0


[GLTSD (Global Logging Target Save Disable) set. Enable Save with '-S on']
SMART Self-test log
Num  Test              Status                 segment  LifeTime  LBA_first_err [SK ASC ASQ]
     Description                              number   (hours)
# 1  Background short  Completed                   -    2539                 - [-   -    -]
# 2  Background short  Completed                   -    2527                 - [-   -    -]
# 3  Background short  Completed                   -    2515                 - [-   -    -]
# 4  Background short  Completed                   -    2503                 - [-   -    -]
# 5  Background short  Completed                   -    2491                 - [-   -    -]
# 6  Background short  Completed                   -    2479                 - [-   -    -]
# 7  Background short  Completed                   -    2467                 - [-   -    -]
# 8  Background short  Completed                   -    2455                 - [-   -    -]
# 9  Background short  Completed                   -    2443                 - [-   -    -]
#10  Background short  Completed                   -    2431                 - [-   -    -]
#11  Background short  Completed                   -    2419                 - [-   -    -]
#12  Background short  Completed                   -    2407                 - [-   -    -]
#13  Background short  Completed                   -    2395                 - [-   -    -]
#14  Background short  Completed                   -    2383                 - [-   -    -]
#15  Background short  Completed                   -    2371                 - [-   -    -]
#16  Background short  Completed                   -    2359                 - [-   -    -]
#17  Background short  Completed                   -    2347                 - [-   -    -]
#18  Background short  Completed                   -    2335                 - [-   -    -]
#19  Background short  Completed                   -    2323                 - [-   -    -]
#20  Background short  Completed                   -    2311                 - [-   -    -]

Long (extended) Self Test duration: 26000 seconds [433.3 minutes]

Background scan results log
  Status: waiting until BMS interval timer expires
    Accumulated power on time, hours:minutes 2549:12 [152952 minutes]
    Number of background scans performed: 32,  scan progress: 0.00%
    Number of background medium scans performed: 32

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 2
  number of phys = 1
  phy identifier = 0
    attached device type: SAS or SATA device
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; 6 Gbps
    attached initiator port: ssp=1 stp=1 smp=1
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c5005910e5f9
    attached SAS address = 0x50030480194d7d05
    attached phy identifier = 5
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 4
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 4
     Phy reset problem count: 0
relative target port id = 2
  generation code = 2
  number of phys = 1
  phy identifier = 1
    attached device type: no device attached
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; unknown
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c5005910e5fa
    attached SAS address = 0x0
    attached phy identifier = 0
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da2
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p10 amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               SEAGATE
Product:              ST3000NM0023
Revision:             0004
Compliance:           SPC-4
User Capacity:        3,000,592,982,016 bytes [3.00 TB]
Logical block size:   512 bytes
LB provisioning type: unreported, LBPME=0, LBPRZ=0
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000c5005910ea9f
Serial number:        Z1Y2052N0000W45122RP
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Wed Mar 25 09:49:13 2015 CET
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     29 C
Drive Trip Temperature:        60 C

Manufactured in week 30 of year 2014
Specified cycle count over device lifetime:  10000
Accumulated start-stop cycles:  261
Specified load-unload count over device lifetime:  300000
Accumulated load-unload cycles:  360
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 1436035986
  Blocks received from initiator = 2622535647
  Blocks read from cache and sent to initiator = 1042997128
  Number of read and write commands whose size <= segment size = 9815053
  Number of read and write commands whose size > segment size = 6369

Vendor (Seagate/Hitachi) factory information
  number of hours powered up = 2549.17
  number of minutes until next internal SMART test = 17

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:   2283545757        0         0  2283545757          0       2934.274           0
write:         0        0         0         0          0       2556.085           0

Non-medium error count:        0


[GLTSD (Global Logging Target Save Disable) set. Enable Save with '-S on']
SMART Self-test log
Num  Test              Status                 segment  LifeTime  LBA_first_err [SK ASC ASQ]
     Description                              number   (hours)
# 1  Background short  Completed                   -    2539                 - [-   -    -]
# 2  Background short  Completed                   -    2527                 - [-   -    -]
# 3  Background short  Completed                   -    2515                 - [-   -    -]
# 4  Background short  Completed                   -    2503                 - [-   -    -]
# 5  Background short  Completed                   -    2491                 - [-   -    -]
# 6  Background short  Completed                   -    2479                 - [-   -    -]
# 7  Background short  Completed                   -    2467                 - [-   -    -]
# 8  Background short  Completed                   -    2455                 - [-   -    -]
# 9  Background short  Completed                   -    2443                 - [-   -    -]
#10  Background short  Completed                   -    2431                 - [-   -    -]
#11  Background short  Completed                   -    2419                 - [-   -    -]
#12  Background short  Completed                   -    2407                 - [-   -    -]
#13  Background short  Completed                   -    2395                 - [-   -    -]
#14  Background short  Completed                   -    2383                 - [-   -    -]
#15  Background short  Completed                   -    2371                 - [-   -    -]
#16  Background short  Completed                   -    2359                 - [-   -    -]
#17  Background short  Completed                   -    2347                 - [-   -    -]
#18  Background short  Completed                   -    2335                 - [-   -    -]
#19  Background short  Completed                   -    2323                 - [-   -    -]
#20  Background short  Completed                   -    2311                 - [-   -    -]

Long (extended) Self Test duration: 26000 seconds [433.3 minutes]

Background scan results log
  Status: waiting until BMS interval timer expires
    Accumulated power on time, hours:minutes 2549:10 [152950 minutes]
    Number of background scans performed: 32,  scan progress: 0.00%
    Number of background medium scans performed: 32

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 2
  number of phys = 1
  phy identifier = 0
    attached device type: SAS or SATA device
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; 6 Gbps
    attached initiator port: ssp=1 stp=1 smp=1
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c5005910ea9d
    attached SAS address = 0x50030480194d7d04
    attached phy identifier = 4
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 2
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 2
     Phy reset problem count: 0
relative target port id = 2
  generation code = 2
  number of phys = 1
  phy identifier = 1
    attached device type: no device attached
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; unknown
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c5005910ea9e
    attached SAS address = 0x0
    attached phy identifier = 0
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da1
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p10 amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               SEAGATE
Product:              ST3000NM0023
Revision:             0004
Compliance:           SPC-4
User Capacity:        3,000,592,982,016 bytes [3.00 TB]
Logical block size:   512 bytes
LB provisioning type: unreported, LBPME=0, LBPRZ=0
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000c500591df9d3
Serial number:        Z1Z544ZL0000W5029RCG
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Wed Mar 25 09:49:13 2015 CET
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     29 C
Drive Trip Temperature:        60 C

Manufactured in week 30 of year 2014
Specified cycle count over device lifetime:  10000
Accumulated start-stop cycles:  106
Specified load-unload count over device lifetime:  300000
Accumulated load-unload cycles:  205
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 1423367083
  Blocks received from initiator = 2641089506
  Blocks read from cache and sent to initiator = 1034849110
  Number of read and write commands whose size <= segment size = 9864121
  Number of read and write commands whose size > segment size = 6437

Vendor (Seagate/Hitachi) factory information
  number of hours powered up = 2549.20
  number of minutes until next internal SMART test = 17

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:   615738934        0         0  615738934          0       2927.787           0
write:         0        0         0         0          0       2296.034           0

Non-medium error count:       26


[GLTSD (Global Logging Target Save Disable) set. Enable Save with '-S on']
SMART Self-test log
Num  Test              Status                 segment  LifeTime  LBA_first_err [SK ASC ASQ]
     Description                              number   (hours)
# 1  Background short  Completed                   -    2547                 - [-   -    -]
# 2  Background short  Completed                   -    2543                 - [-   -    -]
# 3  Background short  Completed                   -    2539                 - [-   -    -]
# 4  Background short  Completed                   -    2535                 - [-   -    -]
# 5  Background short  Completed                   -    2531                 - [-   -    -]
# 6  Background short  Completed                   -    2527                 - [-   -    -]
# 7  Background short  Completed                   -    2523                 - [-   -    -]
# 8  Background short  Completed                   -    2519                 - [-   -    -]
# 9  Background short  Completed                   -    2515                 - [-   -    -]
#10  Background short  Completed                   -    2511                 - [-   -    -]
#11  Background short  Completed                   -    2507                 - [-   -    -]
#12  Background short  Completed                   -    2503                 - [-   -    -]
#13  Background short  Completed                   -    2499                 - [-   -    -]
#14  Background short  Completed                   -    2495                 - [-   -    -]
#15  Background short  Completed                   -    2491                 - [-   -    -]
#16  Background short  Completed                   -    2487                 - [-   -    -]
#17  Background short  Completed                   -    2483                 - [-   -    -]
#18  Background short  Completed                   -    2479                 - [-   -    -]
#19  Background short  Completed                   -    2475                 - [-   -    -]
#20  Background short  Completed                   -    2471                 - [-   -    -]

Long (extended) Self Test duration: 26000 seconds [433.3 minutes]

Background scan results log
  Status: waiting until BMS interval timer expires
    Accumulated power on time, hours:minutes 2549:12 [152952 minutes]
    Number of background scans performed: 32,  scan progress: 0.00%
    Number of background medium scans performed: 32

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 2
  number of phys = 1
  phy identifier = 0
    attached device type: SAS or SATA device
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; 6 Gbps
    attached initiator port: ssp=1 stp=1 smp=1
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c500591df9d1
    attached SAS address = 0x50030480194d7d01
    attached phy identifier = 1
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 2
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 2
     Phy reset problem count: 0
relative target port id = 2
  generation code = 2
  number of phys = 1
  phy identifier = 1
    attached device type: no device attached
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; unknown
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c500591df9d2
    attached SAS address = 0x0
    attached phy identifier = 0
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da0
smartctl 6.3 2014-07-26 r3976 [FreeBSD 9.3-RELEASE-p10 amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               SEAGATE
Product:              ST3000NM0023
Revision:             0004
Compliance:           SPC-4
User Capacity:        3,000,592,982,016 bytes [3.00 TB]
Logical block size:   512 bytes
LB provisioning type: unreported, LBPME=0, LBPRZ=0
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000c50058f88f33
Serial number:        Z1Z4QYS40000C451AW6G
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Wed Mar 25 09:49:15 2015 CET
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     29 C
Drive Trip Temperature:        60 C

Manufactured in week 30 of year 2014
Specified cycle count over device lifetime:  10000
Accumulated start-stop cycles:  212
Specified load-unload count over device lifetime:  300000
Accumulated load-unload cycles:  511
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 1423600374
  Blocks received from initiator = 2747953981
  Blocks read from cache and sent to initiator = 1035233438
  Number of read and write commands whose size <= segment size = 9849937
  Number of read and write commands whose size > segment size = 6027

Vendor (Seagate/Hitachi) factory information
  number of hours powered up = 2549.20
  number of minutes until next internal SMART test = 17

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:   693564151        0         0  693564151          0       2927.907           0
write:         0        0         0         0          0       2148.114           0

Non-medium error count:        0


[GLTSD (Global Logging Target Save Disable) set. Enable Save with '-S on']
SMART Self-test log
Num  Test              Status                 segment  LifeTime  LBA_first_err [SK ASC ASQ]
     Description                              number   (hours)
# 1  Background short  Completed                   -    2547                 - [-   -    -]
# 2  Background short  Completed                   -    2543                 - [-   -    -]
# 3  Background short  Completed                   -    2539                 - [-   -    -]
# 4  Background short  Completed                   -    2535                 - [-   -    -]
# 5  Background short  Completed                   -    2531                 - [-   -    -]
# 6  Background short  Completed                   -    2527                 - [-   -    -]
# 7  Background short  Completed                   -    2523                 - [-   -    -]
# 8  Background short  Completed                   -    2519                 - [-   -    -]
# 9  Background short  Completed                   -    2515                 - [-   -    -]
#10  Background short  Completed                   -    2511                 - [-   -    -]
#11  Background short  Completed                   -    2507                 - [-   -    -]
#12  Background short  Completed                   -    2503                 - [-   -    -]
#13  Background short  Completed                   -    2499                 - [-   -    -]
#14  Background short  Completed                   -    2495                 - [-   -    -]
#15  Background short  Completed                   -    2491                 - [-   -    -]
#16  Background short  Completed                   -    2487                 - [-   -    -]
#17  Background short  Completed                   -    2483                 - [-   -    -]
#18  Background short  Completed                   -    2479                 - [-   -    -]
#19  Background short  Completed                   -    2475                 - [-   -    -]
#20  Background short  Completed                   -    2471                 - [-   -    -]

Long (extended) Self Test duration: 26000 seconds [433.3 minutes]

Background scan results log
  Status: waiting until BMS interval timer expires
    Accumulated power on time, hours:minutes 2549:12 [152952 minutes]
    Number of background scans performed: 32,  scan progress: 0.00%
    Number of background medium scans performed: 32

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 0
  number of phys = 1
  phy identifier = 0
    attached device type: SAS or SATA device
    attached reason: power on
    reason: loss of dword synchronization
    negotiated logical link rate: phy enabled; 6 Gbps
    attached initiator port: ssp=1 stp=1 smp=1
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c50058f88f31
    attached SAS address = 0x50030480194d7d00
    attached phy identifier = 0
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 2
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 2
     Phy reset problem count: 0
relative target port id = 2
  generation code = 0
  number of phys = 1
  phy identifier = 1
    attached device type: no device attached
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; unknown
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c50058f88f32
    attached SAS address = 0x0
    attached phy identifier = 0
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0



