+--------------------------------------------------------------------------------+
+                               SMART @1504201509                                +
+--------------------------------------------------------------------------------+
/dev/da24
smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.0-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Western Digital Elements / My Passport (USB, AF)
Device Model:     WDC WD20NMVW-11EDZS3
Serial Number:    WD-WXQ1EB53203W
LU WWN Device Id: 5 0014ee 20d4b65ed
Firmware Version: 01.01A01
User Capacity:    2,000,365,380,096 bytes [2.00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5200 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ACS-2 (minor revision not indicated)
SATA Version is:  SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is:    Thu Aug 31 10:45:14 2017 PDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Unavailable
APM level is:     128 (minimum power consumption without standby)
Rd look-ahead is: Enabled
Write cache is:   Enabled
ATA Security is:  Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(37320) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 ( 412) minutes.
Conveyance self-test routine
recommended polling time: 	 (   5) minutes.
SCT capabilities: 	       (0x7035)	SCT Status supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR-K   200   200   051    -    0
  3 Spin_Up_Time            POS--K   190   185   021    -    5475
  4 Start_Stop_Count        -O--CK   100   100   000    -    665
  5 Reallocated_Sector_Ct   PO--CK   200   200   140    -    0
  7 Seek_Error_Rate         -OSR-K   200   200   000    -    0
  9 Power_On_Hours          -O--CK   098   098   000    -    1937
 10 Spin_Retry_Count        -O--CK   100   100   000    -    0
 11 Calibration_Retry_Count -O--CK   100   253   000    -    0
 12 Power_Cycle_Count       -O--CK   100   100   000    -    18
192 Power-Off_Retract_Count -O--CK   200   200   000    -    9
193 Load_Cycle_Count        -O--CK   199   199   000    -    3506
194 Temperature_Celsius     -O---K   128   105   000    -    24
196 Reallocated_Event_Count -O--CK   200   200   000    -    0
197 Current_Pending_Sector  -O--CK   200   200   000    -    0
198 Offline_Uncorrectable   ----CK   100   253   000    -    0
199 UDMA_CRC_Error_Count    -O--CK   200   200   000    -    0
200 Multi_Zone_Error_Rate   ---R--   100   253   000    -    0
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      5  Comprehensive SMART error log
0x03       GPL     R/O      6  Ext. Comprehensive SMART error log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      1  Extended self-test log
0x09           SL  R/W      1  Selective self-test log
0x10       GPL     R/O      1  SATA NCQ Queued Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xa0-0xa7  GPL,SL  VS      16  Device vendor specific log
0xa8-0xb6  GPL,SL  VS       1  Device vendor specific log
0xb7       GPL,SL  VS      39  Device vendor specific log
0xbd       GPL,SL  VS       1  Device vendor specific log
0xc0       GPL,SL  VS       1  Device vendor specific log
0xc1       GPL     VS      93  Device vendor specific log
0xcf       GPL     VS   65535  Device vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
No Errors Logged

SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  3
SCT Version (vendor specific):       258 (0x0102)
SCT Support Level:                   1
Device State:                        Active (0)
Current Temperature:                    24 Celsius
Power Cycle Min/Max Temperature:     23/28 Celsius
Lifetime    Min/Max Temperature:     17/48 Celsius
Under/Over Temperature Limit Count:   0/0
Vendor specific:
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:      0/60 Celsius
Min/Max Temperature Limit:           -41/85 Celsius
Temperature History Size (Index):    128 (41)

Index    Estimated Time   Temperature Celsius
  42    2017-08-31 08:38    23  ****
 ...    ..( 41 skipped).    ..  ****
  84    2017-08-31 09:20    23  ****
  85    2017-08-31 09:21    24  *****
  86    2017-08-31 09:22    23  ****
 ...    ..( 15 skipped).    ..  ****
 102    2017-08-31 09:38    23  ****
 103    2017-08-31 09:39    24  *****
 104    2017-08-31 09:40    24  *****
 105    2017-08-31 09:41    24  *****
 106    2017-08-31 09:42    23  ****
 107    2017-08-31 09:43    23  ****
 108    2017-08-31 09:44    23  ****
 109    2017-08-31 09:45    24  *****
 110    2017-08-31 09:46    23  ****
 111    2017-08-31 09:47    24  *****
 ...    ..(  3 skipped).    ..  *****
 115    2017-08-31 09:51    24  *****
 116    2017-08-31 09:52    23  ****
 117    2017-08-31 09:53    24  *****
 ...    ..( 49 skipped).    ..  *****
  39    2017-08-31 10:43    24  *****
  40    2017-08-31 10:44     ?  -
  41    2017-08-31 10:45    24  *****

SCT Error Recovery Control command not supported

Device Statistics (GP/SMART Log 0x04) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  2            0  Command failed due to ICRC error
0x0002  2            0  R_ERR response for data FIS
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0005  2            0  R_ERR response for non-data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS
0x0008  2            0  Device-to-host non-data FIS retries
0x0009  2            0  Transition from drive PhyRdy to drive PhyNRdy
0x000a  2            1  Device-to-host register FISes sent due to a COMRESET
0x000b  2            0  CRC errors within host-to-device FIS
0x000f  2            0  R_ERR response for host-to-device data FIS, CRC
0x0012  2            0  R_ERR response for host-to-device non-data FIS, CRC
0x8000  4        81551  Vendor specific

/dev/da23
smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.0-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               HGST
Product:              HUS726060AL4210
Revision:             A907
Compliance:           SPC-4
User Capacity:        6,001,175,126,016 bytes [6.00 TB]
Logical block size:   4096 bytes
LU is fully provisioned
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000cca24d3b5ec8
Serial number:        NCH1N64Z
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Thu Aug 31 10:45:15 2017 PDT
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     33 C
Drive Trip Temperature:        85 C

Manufactured in week 35 of year 2016
Specified cycle count over device lifetime:  50000
Accumulated start-stop cycles:  14
Specified load-unload count over device lifetime:  600000
Accumulated load-unload cycles:  44
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 5382861993541632

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:          0        3         0         3     298249      30461.162           0
write:         0        1         0         1      13727      39517.297           0
verify:        0        0         0         0       2049          0.000           0

Non-medium error count:        0

No self-tests have been logged

Background scan results log
  Status: scan is active
    Accumulated power on time, hours:minutes 803:02 [48182 minutes]
    Number of background scans performed: 4,  scan progress: 44.67%
    Number of background medium scans performed: 4

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 6
  number of phys = 1
  phy identifier = 0
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b5ec9
    attached SAS address = 0x5003048017b9867f
    attached phy identifier = 11
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0
relative target port id = 2
  generation code = 6
  number of phys = 1
  phy identifier = 1
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b5eca
    attached SAS address = 0x5003048017b986ff
    attached phy identifier = 11
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da22
smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.0-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               HGST
Product:              HUS726060AL4210
Revision:             A907
Compliance:           SPC-4
User Capacity:        6,001,175,126,016 bytes [6.00 TB]
Logical block size:   4096 bytes
LU is fully provisioned
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000cca24d3b5a70
Serial number:        NCH1MX5Z
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Thu Aug 31 10:45:15 2017 PDT
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     35 C
Drive Trip Temperature:        85 C

Manufactured in week 36 of year 2016
Specified cycle count over device lifetime:  50000
Accumulated start-stop cycles:  14
Specified load-unload count over device lifetime:  600000
Accumulated load-unload cycles:  44
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 5871788336611328

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:          0        0         0         0     122129      30460.143           0
write:         0        0         0         0      23779      43346.331           0
verify:        0        0         0         0       2498          0.000           0

Non-medium error count:        0

No self-tests have been logged

Background scan results log
  Status: scan is active
    Accumulated power on time, hours:minutes 803:36 [48216 minutes]
    Number of background scans performed: 4,  scan progress: 45.61%
    Number of background medium scans performed: 4

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 6
  number of phys = 1
  phy identifier = 0
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b5a71
    attached SAS address = 0x5003048017b9867f
    attached phy identifier = 10
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0
relative target port id = 2
  generation code = 6
  number of phys = 1
  phy identifier = 1
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b5a72
    attached SAS address = 0x5003048017b986ff
    attached phy identifier = 10
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da21
smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.0-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               HGST
Product:              HUS726060AL4210
Revision:             A907
Compliance:           SPC-4
User Capacity:        6,001,175,126,016 bytes [6.00 TB]
Logical block size:   4096 bytes
LU is fully provisioned
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000cca24d3b3e74
Serial number:        NCH1L1DZ
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Thu Aug 31 10:45:15 2017 PDT
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     35 C
Drive Trip Temperature:        85 C

Manufactured in week 35 of year 2016
Specified cycle count over device lifetime:  50000
Accumulated start-stop cycles:  14
Specified load-unload count over device lifetime:  600000
Accumulated load-unload cycles:  43
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 6482423265099776

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:          0        0         0         0      49166      21969.191           0
write:         0        0         0         0      23033      35459.415           0
verify:        0        0         0         0       1885          0.000           0

Non-medium error count:        0

No self-tests have been logged

Background scan results log
  Status: scan is active
    Accumulated power on time, hours:minutes 803:07 [48187 minutes]
    Number of background scans performed: 4,  scan progress: 46.22%
    Number of background medium scans performed: 4

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 6
  number of phys = 1
  phy identifier = 0
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b3e75
    attached SAS address = 0x5003048017b9867f
    attached phy identifier = 9
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0
relative target port id = 2
  generation code = 6
  number of phys = 1
  phy identifier = 1
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b3e76
    attached SAS address = 0x5003048017b986ff
    attached phy identifier = 9
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da20
smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.0-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               HGST
Product:              HUS726060AL4210
Revision:             A907
Compliance:           SPC-4
User Capacity:        6,001,175,126,016 bytes [6.00 TB]
Logical block size:   4096 bytes
LU is fully provisioned
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000cca24d3b5d6c
Serial number:        NCH1N3AZ
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Thu Aug 31 10:45:15 2017 PDT
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     32 C
Drive Trip Temperature:        85 C

Manufactured in week 35 of year 2016
Specified cycle count over device lifetime:  50000
Accumulated start-stop cycles:  14
Specified load-unload count over device lifetime:  600000
Accumulated load-unload cycles:  43
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 5446509550108672

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:          0        1         0         1     298917      30458.550           0
write:         0        0         0         0      11337      40027.741           0
verify:        0        0         0         0       1803          0.000           0

Non-medium error count:        0

No self-tests have been logged

Background scan results log
  Status: scan is active
    Accumulated power on time, hours:minutes 802:54 [48174 minutes]
    Number of background scans performed: 4,  scan progress: 43.38%
    Number of background medium scans performed: 4

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 6
  number of phys = 1
  phy identifier = 0
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b5d6d
    attached SAS address = 0x5003048017b9867f
    attached phy identifier = 8
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0
relative target port id = 2
  generation code = 6
  number of phys = 1
  phy identifier = 1
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b5d6e
    attached SAS address = 0x5003048017b986ff
    attached phy identifier = 8
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da19
smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.0-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               HGST
Product:              HUS726060AL4210
Revision:             A907
Compliance:           SPC-4
User Capacity:        6,001,175,126,016 bytes [6.00 TB]
Logical block size:   4096 bytes
LU is fully provisioned
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000cca24d3b5c70
Serial number:        NCH1N19Z
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Thu Aug 31 10:45:15 2017 PDT
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     34 C
Drive Trip Temperature:        85 C

Manufactured in week 35 of year 2016
Specified cycle count over device lifetime:  50000
Accumulated start-stop cycles:  14
Specified load-unload count over device lifetime:  600000
Accumulated load-unload cycles:  52
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 5552543266504704

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:          0       10         0        10     304233      30450.117           0
write:         0        3         0         3      22693      40870.815           0
verify:        0        0         0         0      10814          0.000           0

Non-medium error count:        0

No self-tests have been logged

Background scan results log
  Status: scan is active
    Accumulated power on time, hours:minutes 803:51 [48231 minutes]
    Number of background scans performed: 4,  scan progress: 47.30%
    Number of background medium scans performed: 4

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 6
  number of phys = 1
  phy identifier = 0
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b5c71
    attached SAS address = 0x5003048017b9867f
    attached phy identifier = 7
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0
relative target port id = 2
  generation code = 6
  number of phys = 1
  phy identifier = 1
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b5c72
    attached SAS address = 0x5003048017b986ff
    attached phy identifier = 7
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da18
smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.0-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               HGST
Product:              HUS726060AL4210
Revision:             A907
Compliance:           SPC-4
User Capacity:        6,001,175,126,016 bytes [6.00 TB]
Logical block size:   4096 bytes
LU is fully provisioned
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000cca24d3b5dfc
Serial number:        NCH1N4HZ
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Thu Aug 31 10:45:16 2017 PDT
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     33 C
Drive Trip Temperature:        85 C

Manufactured in week 35 of year 2016
Specified cycle count over device lifetime:  50000
Accumulated start-stop cycles:  14
Specified load-unload count over device lifetime:  600000
Accumulated load-unload cycles:  43
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 5445684782170112

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:          0        2         0         2     297703      30469.313           0
write:         0        4         0         4      12624      40018.295           0
verify:        0        0         0         0       1599          0.000           0

Non-medium error count:        0

No self-tests have been logged

Background scan results log
  Status: scan is active
    Accumulated power on time, hours:minutes 803:20 [48200 minutes]
    Number of background scans performed: 4,  scan progress: 45.71%
    Number of background medium scans performed: 4

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 6
  number of phys = 1
  phy identifier = 0
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b5dfd
    attached SAS address = 0x5003048017b9867f
    attached phy identifier = 6
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0
relative target port id = 2
  generation code = 6
  number of phys = 1
  phy identifier = 1
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b5dfe
    attached SAS address = 0x5003048017b986ff
    attached phy identifier = 6
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da17
smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.0-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               HGST
Product:              HUS726060AL4210
Revision:             A907
Compliance:           SPC-4
User Capacity:        6,001,175,126,016 bytes [6.00 TB]
Logical block size:   4096 bytes
LU is fully provisioned
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000cca24d3b6098
Serial number:        NCH1N9WZ
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Thu Aug 31 10:45:16 2017 PDT
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     33 C
Drive Trip Temperature:        85 C

Manufactured in week 35 of year 2016
Specified cycle count over device lifetime:  50000
Accumulated start-stop cycles:  15
Specified load-unload count over device lifetime:  600000
Accumulated load-unload cycles:  44
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 5429222440960000

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:          0        0         0         0     297839      30452.485           0
write:         0        0         0         0      18305      39877.614           0
verify:        0        0         0         0       1928          0.000           0

Non-medium error count:        0

No self-tests have been logged

Background scan results log
  Status: scan is active
    Accumulated power on time, hours:minutes 802:58 [48178 minutes]
    Number of background scans performed: 4,  scan progress: 44.79%
    Number of background medium scans performed: 4

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 6
  number of phys = 1
  phy identifier = 0
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b6099
    attached SAS address = 0x5003048017b9867f
    attached phy identifier = 5
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0
relative target port id = 2
  generation code = 6
  number of phys = 1
  phy identifier = 1
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b609a
    attached SAS address = 0x5003048017b986ff
    attached phy identifier = 5
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da16
smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.0-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               HGST
Product:              HUS726060AL4210
Revision:             A907
Compliance:           SPC-4
User Capacity:        6,001,175,126,016 bytes [6.00 TB]
Logical block size:   4096 bytes
LU is fully provisioned
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000cca24d3b4964
Serial number:        NCH1LSZZ
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Thu Aug 31 10:45:16 2017 PDT
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     35 C
Drive Trip Temperature:        85 C

Manufactured in week 35 of year 2016
Specified cycle count over device lifetime:  50000
Accumulated start-stop cycles:  14
Specified load-unload count over device lifetime:  600000
Accumulated load-unload cycles:  44
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 5321159134412800

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:          0        1         0         1     298828      30453.371           0
write:         0        0         0         0      24256      39047.742           0
verify:        0        0         0         0       2016          0.000           0

Non-medium error count:        0

No self-tests have been logged

Background scan results log
  Status: scan is active
    Accumulated power on time, hours:minutes 803:22 [48202 minutes]
    Number of background scans performed: 4,  scan progress: 42.62%
    Number of background medium scans performed: 4

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 6
  number of phys = 1
  phy identifier = 0
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b4965
    attached SAS address = 0x5003048017b9867f
    attached phy identifier = 4
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0
relative target port id = 2
  generation code = 6
  number of phys = 1
  phy identifier = 1
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b4966
    attached SAS address = 0x5003048017b986ff
    attached phy identifier = 4
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da15
smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.0-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               HGST
Product:              HUS726060AL4210
Revision:             A907
Compliance:           SPC-4
User Capacity:        6,001,175,126,016 bytes [6.00 TB]
Logical block size:   4096 bytes
LU is fully provisioned
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000cca24d198080
Serial number:        NCGG0T6S
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Thu Aug 31 10:45:16 2017 PDT
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     35 C
Drive Trip Temperature:        85 C

Manufactured in week 48 of year 2015
Specified cycle count over device lifetime:  50000
Accumulated start-stop cycles:  9
Specified load-unload count over device lifetime:  600000
Accumulated load-unload cycles:  38
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 2824162624143360

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:          0        0         0         0      21348      12456.201           0
write:         0        0         0         0      15504      19534.822           0
verify:        0        0         0         0       1626          0.000           0

Non-medium error count:        0

No self-tests have been logged

Background scan results log
  Status: scan is active
    Accumulated power on time, hours:minutes 731:31 [43891 minutes]
    Number of background scans performed: 4,  scan progress: 46.31%
    Number of background medium scans performed: 4

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 6
  number of phys = 1
  phy identifier = 0
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d198081
    attached SAS address = 0x5003048017b9867f
    attached phy identifier = 3
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0
relative target port id = 2
  generation code = 6
  number of phys = 1
  phy identifier = 1
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d198082
    attached SAS address = 0x5003048017b986ff
    attached phy identifier = 3
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da14
smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.0-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               HGST
Product:              HUS726060AL4210
Revision:             A907
Compliance:           SPC-4
User Capacity:        6,001,175,126,016 bytes [6.00 TB]
Logical block size:   4096 bytes
LU is fully provisioned
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000cca24d1a8a24
Serial number:        NCGGLGMS
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Thu Aug 31 10:45:16 2017 PDT
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     33 C
Drive Trip Temperature:        85 C

Manufactured in week 48 of year 2015
Specified cycle count over device lifetime:  50000
Accumulated start-stop cycles:  7
Specified load-unload count over device lifetime:  600000
Accumulated load-unload cycles:  35
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 907896812470272

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:          0        0         0         0      21898        453.133           0
write:         0        0         0         0      15397       4573.234           0
verify:        0        0         0         0       2175          0.000           0

Non-medium error count:        0

No self-tests have been logged

Background scan results log
  Status: scan is active
    Accumulated power on time, hours:minutes 688:17 [41297 minutes]
    Number of background scans performed: 4,  scan progress: 44.62%
    Number of background medium scans performed: 4

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 6
  number of phys = 1
  phy identifier = 0
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d1a8a25
    attached SAS address = 0x5003048017b9867f
    attached phy identifier = 2
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0
relative target port id = 2
  generation code = 6
  number of phys = 1
  phy identifier = 1
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d1a8a26
    attached SAS address = 0x5003048017b986ff
    attached phy identifier = 2
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da13
smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.0-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               HGST
Product:              HUS726060AL4210
Revision:             A907
Compliance:           SPC-4
User Capacity:        6,001,175,126,016 bytes [6.00 TB]
Logical block size:   4096 bytes
LU is fully provisioned
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000cca24d3b5c78
Serial number:        NCH1N1BZ
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Thu Aug 31 10:45:16 2017 PDT
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     35 C
Drive Trip Temperature:        85 C

Manufactured in week 35 of year 2016
Specified cycle count over device lifetime:  50000
Accumulated start-stop cycles:  14
Specified load-unload count over device lifetime:  600000
Accumulated load-unload cycles:  47
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 5921142745333760

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:          0        1         0         1     123031      30450.121           0
write:         0        1         0         1      15738      43718.432           0
verify:        0        0         0         0       1944          0.000           0

Non-medium error count:        0

No self-tests have been logged

Background scan results log
  Status: scan is active
    Accumulated power on time, hours:minutes 802:56 [48176 minutes]
    Number of background scans performed: 4,  scan progress: 45.32%
    Number of background medium scans performed: 4

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 6
  number of phys = 1
  phy identifier = 0
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b5c79
    attached SAS address = 0x5003048017b9867f
    attached phy identifier = 1
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0
relative target port id = 2
  generation code = 6
  number of phys = 1
  phy identifier = 1
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b5c7a
    attached SAS address = 0x5003048017b986ff
    attached phy identifier = 1
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da12
smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.0-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               HGST
Product:              HUS726060AL4210
Revision:             A907
Compliance:           SPC-4
User Capacity:        6,001,175,126,016 bytes [6.00 TB]
Logical block size:   4096 bytes
LU is fully provisioned
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000cca24d3b6070
Serial number:        NCH1N9KZ
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Thu Aug 31 10:45:16 2017 PDT
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     34 C
Drive Trip Temperature:        85 C

Manufactured in week 35 of year 2016
Specified cycle count over device lifetime:  50000
Accumulated start-stop cycles:  14
Specified load-unload count over device lifetime:  600000
Accumulated load-unload cycles:  44
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 5899616436355072

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:          0        0         0         0     127052      30464.398           0
write:         0        1         0         1      18988      43568.372           0
verify:        0        0         0         0       1924          0.000           0

Non-medium error count:        0

No self-tests have been logged

Background scan results log
  Status: scan is active
    Accumulated power on time, hours:minutes 803:23 [48203 minutes]
    Number of background scans performed: 4,  scan progress: 46.33%
    Number of background medium scans performed: 4

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 6
  number of phys = 1
  phy identifier = 0
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b6071
    attached SAS address = 0x5003048017b9867f
    attached phy identifier = 0
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0
relative target port id = 2
  generation code = 6
  number of phys = 1
  phy identifier = 1
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b6072
    attached SAS address = 0x5003048017b986ff
    attached phy identifier = 0
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da11
smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.0-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               HGST
Product:              HUS726060AL4210
Revision:             A907
Compliance:           SPC-4
User Capacity:        6,001,175,126,016 bytes [6.00 TB]
Logical block size:   4096 bytes
LU is fully provisioned
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000cca24d3b5ec8
Serial number:        NCH1N64Z
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Thu Aug 31 10:45:16 2017 PDT
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     33 C
Drive Trip Temperature:        85 C

Manufactured in week 35 of year 2016
Specified cycle count over device lifetime:  50000
Accumulated start-stop cycles:  14
Specified load-unload count over device lifetime:  600000
Accumulated load-unload cycles:  44
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 5382861993541632

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:          0        3         0         3     298249      30461.162           0
write:         0        1         0         1      13727      39517.297           0
verify:        0        0         0         0       2049          0.000           0

Non-medium error count:        0

No self-tests have been logged

Background scan results log
  Status: scan is active
    Accumulated power on time, hours:minutes 803:02 [48182 minutes]
    Number of background scans performed: 4,  scan progress: 44.67%
    Number of background medium scans performed: 4

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 6
  number of phys = 1
  phy identifier = 0
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b5ec9
    attached SAS address = 0x5003048017b9867f
    attached phy identifier = 11
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0
relative target port id = 2
  generation code = 6
  number of phys = 1
  phy identifier = 1
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b5eca
    attached SAS address = 0x5003048017b986ff
    attached phy identifier = 11
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da10
smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.0-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               HGST
Product:              HUS726060AL4210
Revision:             A907
Compliance:           SPC-4
User Capacity:        6,001,175,126,016 bytes [6.00 TB]
Logical block size:   4096 bytes
LU is fully provisioned
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000cca24d3b5a70
Serial number:        NCH1MX5Z
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Thu Aug 31 10:45:16 2017 PDT
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     35 C
Drive Trip Temperature:        85 C

Manufactured in week 36 of year 2016
Specified cycle count over device lifetime:  50000
Accumulated start-stop cycles:  14
Specified load-unload count over device lifetime:  600000
Accumulated load-unload cycles:  44
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 5871788336611328

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:          0        0         0         0     122129      30460.143           0
write:         0        0         0         0      23779      43346.331           0
verify:        0        0         0         0       2498          0.000           0

Non-medium error count:        0

No self-tests have been logged

Background scan results log
  Status: scan is active
    Accumulated power on time, hours:minutes 803:36 [48216 minutes]
    Number of background scans performed: 4,  scan progress: 45.61%
    Number of background medium scans performed: 4

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 6
  number of phys = 1
  phy identifier = 0
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b5a71
    attached SAS address = 0x5003048017b9867f
    attached phy identifier = 10
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0
relative target port id = 2
  generation code = 6
  number of phys = 1
  phy identifier = 1
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b5a72
    attached SAS address = 0x5003048017b986ff
    attached phy identifier = 10
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da9
smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.0-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               HGST
Product:              HUS726060AL4210
Revision:             A907
Compliance:           SPC-4
User Capacity:        6,001,175,126,016 bytes [6.00 TB]
Logical block size:   4096 bytes
LU is fully provisioned
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000cca24d3b3e74
Serial number:        NCH1L1DZ
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Thu Aug 31 10:45:17 2017 PDT
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     35 C
Drive Trip Temperature:        85 C

Manufactured in week 35 of year 2016
Specified cycle count over device lifetime:  50000
Accumulated start-stop cycles:  14
Specified load-unload count over device lifetime:  600000
Accumulated load-unload cycles:  43
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 6482423265099776

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:          0        0         0         0      49166      21969.191           0
write:         0        0         0         0      23033      35459.415           0
verify:        0        0         0         0       1885          0.000           0

Non-medium error count:        0

No self-tests have been logged

Background scan results log
  Status: scan is active
    Accumulated power on time, hours:minutes 803:07 [48187 minutes]
    Number of background scans performed: 4,  scan progress: 46.22%
    Number of background medium scans performed: 4

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 6
  number of phys = 1
  phy identifier = 0
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b3e75
    attached SAS address = 0x5003048017b9867f
    attached phy identifier = 9
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0
relative target port id = 2
  generation code = 6
  number of phys = 1
  phy identifier = 1
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b3e76
    attached SAS address = 0x5003048017b986ff
    attached phy identifier = 9
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da8
smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.0-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               HGST
Product:              HUS726060AL4210
Revision:             A907
Compliance:           SPC-4
User Capacity:        6,001,175,126,016 bytes [6.00 TB]
Logical block size:   4096 bytes
LU is fully provisioned
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000cca24d3b5d6c
Serial number:        NCH1N3AZ
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Thu Aug 31 10:45:17 2017 PDT
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     32 C
Drive Trip Temperature:        85 C

Manufactured in week 35 of year 2016
Specified cycle count over device lifetime:  50000
Accumulated start-stop cycles:  14
Specified load-unload count over device lifetime:  600000
Accumulated load-unload cycles:  43
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 5446509550108672

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:          0        1         0         1     298917      30458.550           0
write:         0        0         0         0      11337      40027.741           0
verify:        0        0         0         0       1803          0.000           0

Non-medium error count:        0

No self-tests have been logged

Background scan results log
  Status: scan is active
    Accumulated power on time, hours:minutes 802:54 [48174 minutes]
    Number of background scans performed: 4,  scan progress: 43.38%
    Number of background medium scans performed: 4

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 6
  number of phys = 1
  phy identifier = 0
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b5d6d
    attached SAS address = 0x5003048017b9867f
    attached phy identifier = 8
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0
relative target port id = 2
  generation code = 6
  number of phys = 1
  phy identifier = 1
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b5d6e
    attached SAS address = 0x5003048017b986ff
    attached phy identifier = 8
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da7
smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.0-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               HGST
Product:              HUS726060AL4210
Revision:             A907
Compliance:           SPC-4
User Capacity:        6,001,175,126,016 bytes [6.00 TB]
Logical block size:   4096 bytes
LU is fully provisioned
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000cca24d3b5c70
Serial number:        NCH1N19Z
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Thu Aug 31 10:45:17 2017 PDT
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     34 C
Drive Trip Temperature:        85 C

Manufactured in week 35 of year 2016
Specified cycle count over device lifetime:  50000
Accumulated start-stop cycles:  14
Specified load-unload count over device lifetime:  600000
Accumulated load-unload cycles:  52
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 5552543266504704

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:          0       10         0        10     304233      30450.117           0
write:         0        3         0         3      22693      40870.815           0
verify:        0        0         0         0      10814          0.000           0

Non-medium error count:        0

No self-tests have been logged

Background scan results log
  Status: scan is active
    Accumulated power on time, hours:minutes 803:51 [48231 minutes]
    Number of background scans performed: 4,  scan progress: 47.30%
    Number of background medium scans performed: 4

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 6
  number of phys = 1
  phy identifier = 0
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b5c71
    attached SAS address = 0x5003048017b9867f
    attached phy identifier = 7
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0
relative target port id = 2
  generation code = 6
  number of phys = 1
  phy identifier = 1
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b5c72
    attached SAS address = 0x5003048017b986ff
    attached phy identifier = 7
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da6
smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.0-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               HGST
Product:              HUS726060AL4210
Revision:             A907
Compliance:           SPC-4
User Capacity:        6,001,175,126,016 bytes [6.00 TB]
Logical block size:   4096 bytes
LU is fully provisioned
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000cca24d3b5dfc
Serial number:        NCH1N4HZ
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Thu Aug 31 10:45:17 2017 PDT
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     33 C
Drive Trip Temperature:        85 C

Manufactured in week 35 of year 2016
Specified cycle count over device lifetime:  50000
Accumulated start-stop cycles:  14
Specified load-unload count over device lifetime:  600000
Accumulated load-unload cycles:  43
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 5445684782170112

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:          0        2         0         2     297703      30469.313           0
write:         0        4         0         4      12624      40018.295           0
verify:        0        0         0         0       1599          0.000           0

Non-medium error count:        0

No self-tests have been logged

Background scan results log
  Status: scan is active
    Accumulated power on time, hours:minutes 803:20 [48200 minutes]
    Number of background scans performed: 4,  scan progress: 45.71%
    Number of background medium scans performed: 4

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 6
  number of phys = 1
  phy identifier = 0
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b5dfd
    attached SAS address = 0x5003048017b9867f
    attached phy identifier = 6
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0
relative target port id = 2
  generation code = 6
  number of phys = 1
  phy identifier = 1
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b5dfe
    attached SAS address = 0x5003048017b986ff
    attached phy identifier = 6
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da5
smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.0-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               HGST
Product:              HUS726060AL4210
Revision:             A907
Compliance:           SPC-4
User Capacity:        6,001,175,126,016 bytes [6.00 TB]
Logical block size:   4096 bytes
LU is fully provisioned
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000cca24d3b6098
Serial number:        NCH1N9WZ
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Thu Aug 31 10:45:17 2017 PDT
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     33 C
Drive Trip Temperature:        85 C

Manufactured in week 35 of year 2016
Specified cycle count over device lifetime:  50000
Accumulated start-stop cycles:  15
Specified load-unload count over device lifetime:  600000
Accumulated load-unload cycles:  44
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 5429222440960000

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:          0        0         0         0     297839      30452.485           0
write:         0        0         0         0      18305      39877.614           0
verify:        0        0         0         0       1928          0.000           0

Non-medium error count:        0

No self-tests have been logged

Background scan results log
  Status: scan is active
    Accumulated power on time, hours:minutes 802:59 [48179 minutes]
    Number of background scans performed: 4,  scan progress: 44.79%
    Number of background medium scans performed: 4

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 6
  number of phys = 1
  phy identifier = 0
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b6099
    attached SAS address = 0x5003048017b9867f
    attached phy identifier = 5
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0
relative target port id = 2
  generation code = 6
  number of phys = 1
  phy identifier = 1
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b609a
    attached SAS address = 0x5003048017b986ff
    attached phy identifier = 5
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da4
smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.0-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               HGST
Product:              HUS726060AL4210
Revision:             A907
Compliance:           SPC-4
User Capacity:        6,001,175,126,016 bytes [6.00 TB]
Logical block size:   4096 bytes
LU is fully provisioned
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000cca24d3b4964
Serial number:        NCH1LSZZ
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Thu Aug 31 10:45:17 2017 PDT
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     35 C
Drive Trip Temperature:        85 C

Manufactured in week 35 of year 2016
Specified cycle count over device lifetime:  50000
Accumulated start-stop cycles:  14
Specified load-unload count over device lifetime:  600000
Accumulated load-unload cycles:  44
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 5321159134412800

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:          0        1         0         1     298828      30453.371           0
write:         0        0         0         0      24256      39047.742           0
verify:        0        0         0         0       2016          0.000           0

Non-medium error count:        0

No self-tests have been logged

Background scan results log
  Status: scan is active
    Accumulated power on time, hours:minutes 803:22 [48202 minutes]
    Number of background scans performed: 4,  scan progress: 42.62%
    Number of background medium scans performed: 4

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 6
  number of phys = 1
  phy identifier = 0
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b4965
    attached SAS address = 0x5003048017b9867f
    attached phy identifier = 4
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0
relative target port id = 2
  generation code = 6
  number of phys = 1
  phy identifier = 1
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b4966
    attached SAS address = 0x5003048017b986ff
    attached phy identifier = 4
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da3
smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.0-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               HGST
Product:              HUS726060AL4210
Revision:             A907
Compliance:           SPC-4
User Capacity:        6,001,175,126,016 bytes [6.00 TB]
Logical block size:   4096 bytes
LU is fully provisioned
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000cca24d198080
Serial number:        NCGG0T6S
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Thu Aug 31 10:45:17 2017 PDT
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     35 C
Drive Trip Temperature:        85 C

Manufactured in week 48 of year 2015
Specified cycle count over device lifetime:  50000
Accumulated start-stop cycles:  9
Specified load-unload count over device lifetime:  600000
Accumulated load-unload cycles:  38
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 2824162624143360

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:          0        0         0         0      21348      12456.201           0
write:         0        0         0         0      15504      19534.822           0
verify:        0        0         0         0       1626          0.000           0

Non-medium error count:        0

No self-tests have been logged

Background scan results log
  Status: scan is active
    Accumulated power on time, hours:minutes 731:31 [43891 minutes]
    Number of background scans performed: 4,  scan progress: 46.31%
    Number of background medium scans performed: 4

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 6
  number of phys = 1
  phy identifier = 0
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d198081
    attached SAS address = 0x5003048017b9867f
    attached phy identifier = 3
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0
relative target port id = 2
  generation code = 6
  number of phys = 1
  phy identifier = 1
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d198082
    attached SAS address = 0x5003048017b986ff
    attached phy identifier = 3
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da2
smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.0-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               HGST
Product:              HUS726060AL4210
Revision:             A907
Compliance:           SPC-4
User Capacity:        6,001,175,126,016 bytes [6.00 TB]
Logical block size:   4096 bytes
LU is fully provisioned
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000cca24d1a8a24
Serial number:        NCGGLGMS
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Thu Aug 31 10:45:18 2017 PDT
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     33 C
Drive Trip Temperature:        85 C

Manufactured in week 48 of year 2015
Specified cycle count over device lifetime:  50000
Accumulated start-stop cycles:  7
Specified load-unload count over device lifetime:  600000
Accumulated load-unload cycles:  35
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 907896812470272

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:          0        0         0         0      21898        453.133           0
write:         0        0         0         0      15397       4573.234           0
verify:        0        0         0         0       2175          0.000           0

Non-medium error count:        0

No self-tests have been logged

Background scan results log
  Status: scan is active
    Accumulated power on time, hours:minutes 688:17 [41297 minutes]
    Number of background scans performed: 4,  scan progress: 44.62%
    Number of background medium scans performed: 4

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 6
  number of phys = 1
  phy identifier = 0
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d1a8a25
    attached SAS address = 0x5003048017b9867f
    attached phy identifier = 2
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0
relative target port id = 2
  generation code = 6
  number of phys = 1
  phy identifier = 1
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d1a8a26
    attached SAS address = 0x5003048017b986ff
    attached phy identifier = 2
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da1
smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.0-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               HGST
Product:              HUS726060AL4210
Revision:             A907
Compliance:           SPC-4
User Capacity:        6,001,175,126,016 bytes [6.00 TB]
Logical block size:   4096 bytes
LU is fully provisioned
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000cca24d3b5c78
Serial number:        NCH1N1BZ
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Thu Aug 31 10:45:18 2017 PDT
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     35 C
Drive Trip Temperature:        85 C

Manufactured in week 35 of year 2016
Specified cycle count over device lifetime:  50000
Accumulated start-stop cycles:  14
Specified load-unload count over device lifetime:  600000
Accumulated load-unload cycles:  47
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 5921142745333760

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:          0        1         0         1     123031      30450.121           0
write:         0        1         0         1      15738      43718.432           0
verify:        0        0         0         0       1944          0.000           0

Non-medium error count:        0

No self-tests have been logged

Background scan results log
  Status: scan is active
    Accumulated power on time, hours:minutes 802:56 [48176 minutes]
    Number of background scans performed: 4,  scan progress: 45.32%
    Number of background medium scans performed: 4

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 6
  number of phys = 1
  phy identifier = 0
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b5c79
    attached SAS address = 0x5003048017b9867f
    attached phy identifier = 1
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0
relative target port id = 2
  generation code = 6
  number of phys = 1
  phy identifier = 1
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b5c7a
    attached SAS address = 0x5003048017b986ff
    attached phy identifier = 1
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/da0
smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.0-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               HGST
Product:              HUS726060AL4210
Revision:             A907
Compliance:           SPC-4
User Capacity:        6,001,175,126,016 bytes [6.00 TB]
Logical block size:   4096 bytes
LU is fully provisioned
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000cca24d3b6070
Serial number:        NCH1N9KZ
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Thu Aug 31 10:45:18 2017 PDT
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     34 C
Drive Trip Temperature:        85 C

Manufactured in week 35 of year 2016
Specified cycle count over device lifetime:  50000
Accumulated start-stop cycles:  14
Specified load-unload count over device lifetime:  600000
Accumulated load-unload cycles:  44
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 5899616436355072

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:          0        0         0         0     127052      30464.398           0
write:         0        1         0         1      18988      43568.372           0
verify:        0        0         0         0       1924          0.000           0

Non-medium error count:        0

No self-tests have been logged

Background scan results log
  Status: scan is active
    Accumulated power on time, hours:minutes 803:23 [48203 minutes]
    Number of background scans performed: 4,  scan progress: 46.33%
    Number of background medium scans performed: 4

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 6
  number of phys = 1
  phy identifier = 0
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b6071
    attached SAS address = 0x5003048017b9867f
    attached phy identifier = 0
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0
relative target port id = 2
  generation code = 6
  number of phys = 1
  phy identifier = 1
    attached device type: expander device
    attached reason: SMP phy control function
    reason: unknown
    negotiated logical link rate: phy enabled; 12 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=1
    SAS address = 0x5000cca24d3b6072
    attached SAS address = 0x5003048017b986ff
    attached phy identifier = 0
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0

/dev/ada3
smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.0-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Device Model:     32GB SATA Flash Drive
Serial Number:    A00172660000000039C5
LU WWN Device Id: 5 dc663a c8b6039c5
Firmware Version: SFDK003L
User Capacity:    32,017,047,552 bytes [32.0 GB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    Solid State Device
Form Factor:      2.5 inches
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   ACS-2 T13/2015-D revision 3
SATA Version is:  SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Thu Aug 31 10:45:18 2017 PDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Unavailable
APM level is:     128 (minimum power consumption without standby)
Rd look-ahead is: Enabled
Write cache is:   Enabled
ATA Security is:  Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(   32) seconds.
Offline data collection
capabilities: 			 (0x5b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 (   1) minutes.
SCT capabilities: 	       (0x0039)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 0
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  9 Power_On_Hours          -O--C-   100   100   000    -    799
 12 Power_Cycle_Count       -O--C-   100   100   000    -    18
163 Unknown_Attribute       ------   100   100   001    -    25
164 Unknown_Attribute       ------   100   100   001    -    14
166 Unknown_Attribute       ------   100   100   010    -    0
167 Unknown_Attribute       -O---K   100   100   000    -    0
168 Unknown_Attribute       -O--C-   100   100   000    -    0
175 Program_Fail_Count_Chip PO--C-   100   100   010    -    0
192 Power-Off_Retract_Count -O--C-   100   100   000    -    16
194 Temperature_Celsius     -O---K   060   060   030    -    40 (Min/Max 30/60)
241 Total_LBAs_Written      -O--CK   100   100   000    -    880069693
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O     51  Comprehensive SMART error log
0x03       GPL     R/O     64  Ext. Comprehensive SMART error log
0x04       GPL,SL  R/O      8  Device Statistics log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      1  Extended self-test log
0x09           SL  R/W      1  Selective self-test log
0x10       GPL     R/O      1  SATA NCQ Queued Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x30       GPL,SL  R/O      9  IDENTIFY DEVICE data log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (64 sectors)
No Errors Logged

SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  3
SCT Version (vendor specific):       1 (0x0001)
SCT Support Level:                   0
Device State:                        Active (0)
Current Temperature:                  0 Celsius
Power Cycle Max Temperature:          0 Celsius
Lifetime    Max Temperature:          0 Celsius

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:     -127/127 Celsius
Min/Max Temperature Limit:           -127/127 Celsius
Temperature History Size (Index):    478 (356)

Index    Estimated Time   Temperature Celsius
 357    2017-08-31 02:48     ?  -
 ...    ..(122 skipped).    ..  -
   2    2017-08-31 04:51     ?  -
   3    2017-08-31 04:52    40  *********************
   4    2017-08-31 04:53     ?  -
   5    2017-08-31 04:54     ?  -
   6    2017-08-31 04:55     ?  -
   7    2017-08-31 04:56    40  *********************
   8    2017-08-31 04:57     ?  -
   9    2017-08-31 04:58     ?  -
  10    2017-08-31 04:59     ?  -
  11    2017-08-31 05:00    40  *********************
  12    2017-08-31 05:01     ?  -
  13    2017-08-31 05:02    40  *********************
 ...    ..( 85 skipped).    ..  *********************
  99    2017-08-31 06:28    40  *********************
 100    2017-08-31 06:29     ?  -
 101    2017-08-31 06:30    40  *********************
 ...    ..( 77 skipped).    ..  *********************
 179    2017-08-31 07:48    40  *********************
 180    2017-08-31 07:49     ?  -
 181    2017-08-31 07:50    40  *********************
 ...    ..( 32 skipped).    ..  *********************
 214    2017-08-31 08:23    40  *********************
 215    2017-08-31 08:24     ?  -
 216    2017-08-31 08:25     ?  -
 217    2017-08-31 08:26    40  *********************
 ...    ..( 72 skipped).    ..  *********************
 290    2017-08-31 09:39    40  *********************
 291    2017-08-31 09:40     ?  -
 292    2017-08-31 09:41    40  *********************
 ...    ..(  6 skipped).    ..  *********************
 299    2017-08-31 09:48    40  *********************
 300    2017-08-31 09:49     ?  -
 301    2017-08-31 09:50    40  *********************
 ...    ..(  3 skipped).    ..  *********************
 305    2017-08-31 09:54    40  *********************
 306    2017-08-31 09:55     ?  -
 307    2017-08-31 09:56    40  *********************
 308    2017-08-31 09:57    40  *********************
 309    2017-08-31 09:58    40  *********************
 310    2017-08-31 09:59     ?  -
 311    2017-08-31 10:00    40  *********************
 ...    ..( 44 skipped).    ..  *********************
 356    2017-08-31 10:45    40  *********************

SCT Error Recovery Control:
           Read:     70 (7.0 seconds)
          Write:     70 (7.0 seconds)

Device Statistics (GP Log 0x04)
Page  Offset Size        Value Flags Description
0x01  =====  =               =  ===  == General Statistics (rev 2) ==
0x01  0x008  4              18  ---  Lifetime Power-On Resets
0x01  0x018  6       880068538  ---  Logical Sectors Written
0x01  0x020  6         3470318  ---  Number of Write Commands
0x01  0x028  6       828605035  ---  Logical Sectors Read
0x01  0x030  6         3305752  ---  Number of Read Commands
0x01  0x038  6      2876400000  ---  Date and Time TimeStamp
0x07  =====  =               =  ===  == Solid State Device Statistics (rev 1) ==
0x07  0x008  1               0  N--  Percentage Used Endurance Indicator
                                |||_ C monitored condition met
                                ||__ D supports DSN
                                |___ N normalized value

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  2            0  Command failed due to ICRC error
0x0002  2            0  R_ERR response for data FIS
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0009  4            2  Transition from drive PhyRdy to drive PhyNRdy
0x000a  4            4  Device-to-host register FISes sent due to a COMRESET
0x000f  2            0  R_ERR response for host-to-device data FIS, CRC

/dev/ada2
smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.0-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Device Model:     32GB SATA Flash Drive
Serial Number:    A00172660000000039C4
LU WWN Device Id: 5 dc663a c8b6039c4
Firmware Version: SFDK003L
User Capacity:    32,017,047,552 bytes [32.0 GB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    Solid State Device
Form Factor:      2.5 inches
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   ACS-2 T13/2015-D revision 3
SATA Version is:  SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Thu Aug 31 10:45:18 2017 PDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Unavailable
APM level is:     128 (minimum power consumption without standby)
Rd look-ahead is: Enabled
Write cache is:   Enabled
ATA Security is:  Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(   32) seconds.
Offline data collection
capabilities: 			 (0x5b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 (   1) minutes.
SCT capabilities: 	       (0x0039)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 0
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  9 Power_On_Hours          -O--C-   100   100   000    -    799
 12 Power_Cycle_Count       -O--C-   100   100   000    -    19
163 Unknown_Attribute       ------   100   100   001    -    25
164 Unknown_Attribute       ------   100   100   001    -    14
166 Unknown_Attribute       ------   100   100   010    -    0
167 Unknown_Attribute       -O---K   100   100   000    -    0
168 Unknown_Attribute       -O--C-   100   100   000    -    0
175 Program_Fail_Count_Chip PO--C-   100   100   010    -    0
192 Power-Off_Retract_Count -O--C-   100   100   000    -    17
194 Temperature_Celsius     -O---K   060   060   030    -    40 (Min/Max 30/60)
241 Total_LBAs_Written      -O--CK   100   100   000    -    880069693
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O     51  Comprehensive SMART error log
0x03       GPL     R/O     64  Ext. Comprehensive SMART error log
0x04       GPL,SL  R/O      8  Device Statistics log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      1  Extended self-test log
0x09           SL  R/W      1  Selective self-test log
0x10       GPL     R/O      1  SATA NCQ Queued Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x30       GPL,SL  R/O      9  IDENTIFY DEVICE data log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (64 sectors)
No Errors Logged

SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  3
SCT Version (vendor specific):       1 (0x0001)
SCT Support Level:                   0
Device State:                        Active (0)
Current Temperature:                  0 Celsius
Power Cycle Max Temperature:          0 Celsius
Lifetime    Max Temperature:          0 Celsius

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:     -127/127 Celsius
Min/Max Temperature Limit:           -127/127 Celsius
Temperature History Size (Index):    478 (434)

Index    Estimated Time   Temperature Celsius
 435    2017-08-31 02:48     ?  -
 ...    ..( 45 skipped).    ..  -
   3    2017-08-31 03:34     ?  -
   4    2017-08-31 03:35    40  *********************
   5    2017-08-31 03:36     ?  -
   6    2017-08-31 03:37     ?  -
   7    2017-08-31 03:38     ?  -
   8    2017-08-31 03:39    40  *********************
   9    2017-08-31 03:40     ?  -
  10    2017-08-31 03:41     ?  -
  11    2017-08-31 03:42     ?  -
  12    2017-08-31 03:43    40  *********************
  13    2017-08-31 03:44     ?  -
  14    2017-08-31 03:45    40  *********************
 ...    ..( 83 skipped).    ..  *********************
  98    2017-08-31 05:09    40  *********************
  99    2017-08-31 05:10     ?  -
 100    2017-08-31 05:11    40  *********************
 ...    ..( 81 skipped).    ..  *********************
 182    2017-08-31 06:33    40  *********************
 183    2017-08-31 06:34     ?  -
 184    2017-08-31 06:35    40  *********************
 ...    ..( 32 skipped).    ..  *********************
 217    2017-08-31 07:08    40  *********************
 218    2017-08-31 07:09     ?  -
 219    2017-08-31 07:10     ?  -
 220    2017-08-31 07:11    40  *********************
 ...    ..( 73 skipped).    ..  *********************
 294    2017-08-31 08:25    40  *********************
 295    2017-08-31 08:26     ?  -
 296    2017-08-31 08:27    40  *********************
 ...    ..(  6 skipped).    ..  *********************
 303    2017-08-31 08:34    40  *********************
 304    2017-08-31 08:35     ?  -
 305    2017-08-31 08:36    40  *********************
 ...    ..(  2 skipped).    ..  *********************
 308    2017-08-31 08:39    40  *********************
 309    2017-08-31 08:40     ?  -
 310    2017-08-31 08:41    40  *********************
 311    2017-08-31 08:42    40  *********************
 312    2017-08-31 08:43    40  *********************
 313    2017-08-31 08:44     ?  -
 314    2017-08-31 08:45    40  *********************
 ...    ..(119 skipped).    ..  *********************
 434    2017-08-31 10:45    40  *********************

SCT Error Recovery Control:
           Read:     70 (7.0 seconds)
          Write:     70 (7.0 seconds)

Device Statistics (GP Log 0x04)
Page  Offset Size        Value Flags Description
0x01  =====  =               =  ===  == General Statistics (rev 2) ==
0x01  0x008  4              19  ---  Lifetime Power-On Resets
0x01  0x018  6       880068538  ---  Logical Sectors Written
0x01  0x020  6         3469536  ---  Number of Write Commands
0x01  0x028  6       825606154  ---  Logical Sectors Read
0x01  0x030  6         3326598  ---  Number of Read Commands
0x01  0x038  6      2876400000  ---  Date and Time TimeStamp
0x07  =====  =               =  ===  == Solid State Device Statistics (rev 1) ==
0x07  0x008  1               0  N--  Percentage Used Endurance Indicator
                                |||_ C monitored condition met
                                ||__ D supports DSN
                                |___ N normalized value

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  2            0  Command failed due to ICRC error
0x0002  2            0  R_ERR response for data FIS
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0009  4            2  Transition from drive PhyRdy to drive PhyNRdy
0x000a  4            4  Device-to-host register FISes sent due to a COMRESET
0x000f  2            0  R_ERR response for host-to-device data FIS, CRC

/dev/ada1
smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.0-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Device Model:     INTEL SSDSC2BB240G7
Serial Number:    PHDV722400GP240AGN
LU WWN Device Id: 5 5cd2e4 14e07ce9c
Firmware Version: N2010112
User Capacity:    240,057,409,536 bytes [240 GB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    Solid State Device
Form Factor:      2.5 inches
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   ACS-3 T13/2161-D revision 5
SATA Version is:  SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Thu Aug 31 10:45:18 2017 PDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Unavailable
APM feature is:   Unavailable
Rd look-ahead is: Enabled
Write cache is:   Enabled
ATA Security is:  Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(    0) seconds.
Offline data collection
capabilities: 			 (0x79) SMART execute Offline immediate.
					No Auto Offline data collection support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 (   2) minutes.
Conveyance self-test routine
recommended polling time: 	 (   2) minutes.
SCT capabilities: 	       (0x003d)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  5 Reallocated_Sector_Ct   -O--CK   100   100   000    -    0
  9 Power_On_Hours          -O--CK   100   100   000    -    805
 12 Power_Cycle_Count       -O--CK   100   100   000    -    18
170 Unknown_Attribute       PO--CK   100   100   010    -    0
171 Unknown_Attribute       -O--CK   100   100   000    -    0
172 Unknown_Attribute       -O--CK   100   100   000    -    0
174 Unknown_Attribute       -O--CK   100   100   000    -    16
175 Program_Fail_Count_Chip PO--CK   100   100   010    -    98825221198
183 Runtime_Bad_Block       -O--CK   100   100   000    -    0
184 End-to-End_Error        PO--CK   100   100   090    -    0
187 Reported_Uncorrect      -O--CK   100   100   000    -    0
190 Airflow_Temperature_Cel -O---K   068   066   000    -    32 (Min/Max 20/35)
192 Power-Off_Retract_Count -O--CK   100   100   000    -    16
194 Temperature_Celsius     -O---K   100   100   000    -    32
197 Current_Pending_Sector  -O--C-   100   100   000    -    0
199 UDMA_CRC_Error_Count    -OSRCK   100   100   000    -    0
225 Unknown_SSD_Attribute   -O--CK   100   100   000    -    251580
226 Unknown_SSD_Attribute   -O--CK   100   100   000    -    552
227 Unknown_SSD_Attribute   -O--CK   100   100   000    -    27
228 Power-off_Retract_Count -O--CK   100   100   000    -    48236
232 Available_Reservd_Space PO--CK   100   100   010    -    0
233 Media_Wearout_Indicator -O--CK   100   100   000    -    0
234 Unknown_Attribute       -O--CK   100   100   000    -    0
241 Total_LBAs_Written      -O--CK   100   100   000    -    251580
242 Total_LBAs_Read         -O--CK   100   100   000    -    95046
243 Unknown_Attribute       -O--CK   100   100   000    -    285680
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      8  Comprehensive SMART error log
0x03       GPL     R/O     20  Ext. Comprehensive SMART error log
0x04       GPL,SL  R/O      8  Device Statistics log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      2  Extended self-test log
0x08       GPL     R/O      2  Power Conditions log
0x09           SL  R/W      1  Selective self-test log
0x10       GPL     R/O      1  SATA NCQ Queued Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x30       GPL,SL  R/O      9  IDENTIFY DEVICE data log
0x80-0x98  GPL,SL  R/W     16  Host vendor specific log
0x9b-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xb8       GPL,SL  VS       1  Device vendor specific log
0xb9       GPL     VS    1704  Device vendor specific log
0xb9       SL      VS     168  Device vendor specific log
0xba       GPL     VS    1280  Device vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      8  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (20 sectors)
No Errors Logged

SMART Extended Self-test Log Version: 1 (2 sectors)
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  3
SCT Version (vendor specific):       1 (0x0001)
SCT Support Level:                   0
Device State:                        Active (0)
Current Temperature:                    32 Celsius
Power Cycle Min/Max Temperature:     20/35 Celsius
Lifetime    Min/Max Temperature:     15/47 Celsius
Under/Over Temperature Limit Count:   0/0
Vendor specific:
00 00 2c 01 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:      0/70 Celsius
Min/Max Temperature Limit:            0/70 Celsius
Temperature History Size (Index):    478 (50)

Index    Estimated Time   Temperature Celsius
  51    2017-08-31 02:48    32  *************
 ...    ..(476 skipped).    ..  *************
  50    2017-08-31 10:45    32  *************

SCT Error Recovery Control:
           Read: Disabled
          Write: Disabled

Device Statistics (GP Log 0x04)
Page  Offset Size        Value Flags Description
0x01  =====  =               =  ===  == General Statistics (rev 2) ==
0x01  0x008  4              18  ---  Lifetime Power-On Resets
0x01  0x018  6     16487607177  ---  Logical Sectors Written
0x01  0x020  6        66809367  ---  Number of Write Commands
0x01  0x028  6      6228959279  ---  Logical Sectors Read
0x01  0x030  6        29986183  ---  Number of Read Commands
0x04  =====  =               =  ===  == General Errors Statistics (rev 1) ==
0x04  0x008  4               0  ---  Number of Reported Uncorrectable Errors
0x04  0x010  4               0  ---  Resets Between Cmd Acceptance and Completion
0x05  =====  =               =  ===  == Temperature Statistics (rev 1) ==
0x05  0x008  1              32  ---  Current Temperature
0x05  0x010  1              32  ---  Average Short Term Temperature
0x05  0x018  1               -  ---  Average Long Term Temperature
0x05  0x020  1              47  ---  Highest Temperature
0x05  0x028  1              25  ---  Lowest Temperature
0x05  0x030  1              39  ---  Highest Average Short Term Temperature
0x05  0x038  1              31  ---  Lowest Average Short Term Temperature
0x05  0x040  1               -  ---  Highest Average Long Term Temperature
0x05  0x048  1               -  ---  Lowest Average Long Term Temperature
0x05  0x050  4               0  ---  Time in Over-Temperature
0x05  0x058  1              70  ---  Specified Maximum Operating Temperature
0x05  0x060  4               0  ---  Time in Under-Temperature
0x05  0x068  1               0  ---  Specified Minimum Operating Temperature
0x06  =====  =               =  ===  == Transport Statistics (rev 1) ==
0x06  0x008  4              64  ---  Number of Hardware Resets
0x06  0x010  4              51  ---  Number of ASR Events
0x06  0x018  4               0  ---  Number of Interface CRC Errors
0x07  =====  =               =  ===  == Solid State Device Statistics (rev 1) ==
0x07  0x008  1               0  ---  Percentage Used Endurance Indicator
                                |||_ C monitored condition met
                                ||__ D supports DSN
                                |___ N normalized value

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  4            0  Command failed due to ICRC error
0x0003  4            0  R_ERR response for device-to-host data FIS
0x0004  4            0  R_ERR response for host-to-device data FIS
0x0006  4            0  R_ERR response for device-to-host non-data FIS
0x000a  4            4  Device-to-host register FISes sent due to a COMRESET
0x000b  4            0  CRC errors within host-to-device FIS
0x000d  4            0  Non-CRC errors within host-to-device FIS

/dev/ada0
smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.0-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Intel 730 and DC S35x0/3610/3700 Series SSDs
Device Model:     INTEL SSDSC2BA200G4
Serial Number:    BTHV7196094E200MGN
LU WWN Device Id: 5 5cd2e4 14dc51cb3
Firmware Version: G2010150
User Capacity:    200,049,647,616 bytes [200 GB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    Solid State Device
Form Factor:      2.5 inches
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ACS-2 T13/2015-D revision 3
SATA Version is:  SATA 2.6, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Thu Aug 31 10:45:18 2017 PDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Unavailable
APM feature is:   Unavailable
Rd look-ahead is: Enabled
Write cache is:   Enabled
ATA Security is:  Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(    0) seconds.
Offline data collection
capabilities: 			 (0x79) SMART execute Offline immediate.
					No Auto Offline data collection support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 (   2) minutes.
Conveyance self-test routine
recommended polling time: 	 (   2) minutes.
SCT capabilities: 	       (0x003d)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  5 Reallocated_Sector_Ct   -O--CK   100   100   000    -    0
  9 Power_On_Hours          -O--CK   100   100   000    -    805
 12 Power_Cycle_Count       -O--CK   100   100   000    -    19
170 Available_Reservd_Space PO--CK   100   100   010    -    0
171 Program_Fail_Count      -O--CK   100   100   000    -    0
172 Erase_Fail_Count        -O--CK   100   100   000    -    0
174 Unsafe_Shutdown_Count   -O--CK   100   100   000    -    16
175 Power_Loss_Cap_Test     PO--CK   100   100   010    -    4830 (5 625)
183 SATA_Downshift_Count    -O--CK   100   100   000    -    0
184 End-to-End_Error        PO--CK   100   100   090    -    0
187 Reported_Uncorrect      -O--CK   100   100   000    -    0
190 Temperature_Case        -O---K   067   065   000    -    33 (Min/Max 25/35)
192 Unsafe_Shutdown_Count   -O--CK   100   100   000    -    16
194 Temperature_Internal    -O---K   100   100   000    -    33
197 Current_Pending_Sector  -O--C-   100   100   000    -    0
199 CRC_Error_Count         -OSRCK   100   100   000    -    0
225 Host_Writes_32MiB       -O--CK   100   100   000    -    83485
226 Workld_Media_Wear_Indic -O--CK   100   100   000    -    40
227 Workld_Host_Reads_Perc  -O--CK   100   100   000    -    49
228 Workload_Minutes        -O--CK   100   100   000    -    48235
232 Available_Reservd_Space PO--CK   100   100   010    -    0
233 Media_Wearout_Indicator -O--CK   100   100   000    -    0
234 Thermal_Throttle        -O--CK   100   100   000    -    0/0
241 Host_Writes_32MiB       -O--CK   100   100   000    -    83485
242 Host_Reads_32MiB        -O--CK   100   100   000    -    80721
243 NAND_Writes_32MiB       -O--CK   100   100   000    -    93947
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01       GPL,SL  R/O      1  Summary SMART error log
0x02       GPL,SL  R/O      8  Comprehensive SMART error log
0x03       GPL,SL  R/O     20  Ext. Comprehensive SMART error log
0x04       GPL,SL  R/O      8  Device Statistics log
0x06       GPL,SL  R/O      1  SMART self-test log
0x07       GPL,SL  R/O      2  Extended self-test log
0x08       GPL,SL  R/O      2  Power Conditions log
0x09       GPL,SL  R/W      1  Selective self-test log
0x10       GPL,SL  R/O      1  SATA NCQ Queued Error log
0x11       GPL,SL  R/O      1  SATA Phy Event Counters log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xb0       GPL,SL  VS       1  Device vendor specific log
0xb1       GPL,SL  VS      33  Device vendor specific log
0xb8       GPL,SL  VS       1  Device vendor specific log
0xb9       GPL     VS    1544  Device vendor specific log
0xb9       SL      VS       8  Device vendor specific log
0xba       GPL     VS    1280  Device vendor specific log
0xdf       GPL,SL  VS       1  Device vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (20 sectors)
No Errors Logged

SMART Extended Self-test Log Version: 1 (2 sectors)
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  3
SCT Version (vendor specific):       1 (0x0001)
SCT Support Level:                   0
Device State:                        Active (0)
Current Temperature:                    33 Celsius
Power Cycle Min/Max Temperature:     25/35 Celsius
Lifetime    Min/Max Temperature:     20/51 Celsius
Under/Over Temperature Limit Count:   0/0
Vendor specific:
00 00 64 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:      0/70 Celsius
Min/Max Temperature Limit:            0/70 Celsius
Temperature History Size (Index):    478 (47)

Index    Estimated Time   Temperature Celsius
  48    2017-08-31 02:48    33  **************
 ...    ..(476 skipped).    ..  **************
  47    2017-08-31 10:45    33  **************

SCT Error Recovery Control:
           Read: Disabled
          Write: Disabled

Device Statistics (GP Log 0x04)
Page  Offset Size        Value Flags Description
0x01  =====  =               =  ===  == General Statistics (rev 2) ==
0x01  0x008  4              19  ---  Lifetime Power-On Resets
0x01  0x018  6      5471275609  ---  Logical Sectors Written
0x01  0x020  6        21392894  ---  Number of Write Commands
0x01  0x028  6      5290148933  ---  Logical Sectors Read
0x01  0x030  6        20691111  ---  Number of Read Commands
0x04  =====  =               =  ===  == General Errors Statistics (rev 1) ==
0x04  0x008  4               0  ---  Number of Reported Uncorrectable Errors
0x04  0x010  4               0  ---  Resets Between Cmd Acceptance and Completion
0x05  =====  =               =  ===  == Temperature Statistics (rev 1) ==
0x05  0x008  1              33  ---  Current Temperature
0x05  0x010  1              33  ---  Average Short Term Temperature
0x05  0x018  1               -  ---  Average Long Term Temperature
0x05  0x020  1              51  ---  Highest Temperature
0x05  0x028  1              25  ---  Lowest Temperature
0x05  0x030  1              39  ---  Highest Average Short Term Temperature
0x05  0x038  1              32  ---  Lowest Average Short Term Temperature
0x05  0x040  1               -  ---  Highest Average Long Term Temperature
0x05  0x048  1               -  ---  Lowest Average Long Term Temperature
0x05  0x050  4               0  ---  Time in Over-Temperature
0x05  0x058  1              70  ---  Specified Maximum Operating Temperature
0x05  0x060  4               0  ---  Time in Under-Temperature
0x05  0x068  1               0  ---  Specified Minimum Operating Temperature
0x06  =====  =               =  ===  == Transport Statistics (rev 1) ==
0x06  0x008  4              63  ---  Number of Hardware Resets
0x06  0x010  4              50  ---  Number of ASR Events
0x06  0x018  4               0  ---  Number of Interface CRC Errors
0x07  =====  =               =  ===  == Solid State Device Statistics (rev 1) ==
0x07  0x008  1               0  ---  Percentage Used Endurance Indicator
                                |||_ C monitored condition met
                                ||__ D supports DSN
                                |___ N normalized value

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  4            0  Command failed due to ICRC error
0x0003  4            0  R_ERR response for device-to-host data FIS
0x0004  4            0  R_ERR response for host-to-device data FIS
0x0006  4            0  R_ERR response for device-to-host non-data FIS
0x000a  4            4  Device-to-host register FISes sent due to a COMRESET
0x000b  4            0  CRC errors within host-to-device FIS
0x000d  4            0  Non-CRC errors within host-to-device FIS

debug finished in 9 seconds for SMART


