+--------------------------------------------------------------------------------+
+                       SMART - 'smartctl -x' @1555468784                        +
+--------------------------------------------------------------------------------+
/dev/ada3
smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.1-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Device Model:     WDC WD100EFAX-68LHPN0
Serial Number:    JEHKHTXN
LU WWN Device Id: 5 000cca 267d60d23
Firmware Version: 83.H0A83
User Capacity:    10,000,831,348,736 bytes [10.0 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5400 rpm
Form Factor:      3.5 inches
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   ACS-2, ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Tue Apr 16 19:39:44 2019 PDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Unavailable
APM feature is:   Disabled
Rd look-ahead is: Enabled
Write cache is:   Enabled
ATA Security is:  Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x80)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(   93) seconds.
Offline data collection
capabilities: 			 (0x5b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 (1144) minutes.
SCT capabilities: 	       (0x003d)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     PO-R--   100   100   016    -    0
  2 Throughput_Performance  --S---   130   130   054    -    108
  3 Spin_Up_Time            POS---   253   253   024    -    45 (Average 45)
  4 Start_Stop_Count        -O--C-   100   100   000    -    1107
  5 Reallocated_Sector_Ct   PO--CK   100   100   005    -    0
  7 Seek_Error_Rate         -O-R--   100   100   067    -    0
  8 Seek_Time_Performance   --S---   128   128   020    -    18
  9 Power_On_Hours          -O--C-   100   100   000    -    1274
 10 Spin_Retry_Count        -O--C-   100   100   060    -    0
 12 Power_Cycle_Count       -O--CK   100   100   000    -    1107
 22 Unknown_Attribute       PO---K   100   100   025    -    100
192 Power-Off_Retract_Count -O--CK   100   100   000    -    1155
193 Load_Cycle_Count        -O--C-   100   100   000    -    1155
194 Temperature_Celsius     -O----   162   162   000    -    40 (Min/Max 18/51)
196 Reallocated_Event_Count -O--CK   100   100   000    -    0
197 Current_Pending_Sector  -O---K   100   100   000    -    0
198 Offline_Uncorrectable   ---R--   100   100   000    -    0
199 UDMA_CRC_Error_Count    -O-R--   200   200   000    -    0
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      1  Comprehensive SMART error log
0x03       GPL     R/O      1  Ext. Comprehensive SMART error log
0x04       GPL     R/O    256  Device Statistics log
0x04       SL      R/O    255  Device Statistics log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      1  Extended self-test log
0x08       GPL     R/O      2  Power Conditions log
0x09           SL  R/W      1  Selective self-test log
0x0c       GPL     R/O   5501  Pending Defects log
0x10       GPL     R/O      1  SATA NCQ Queued Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x12       GPL     R/O      1  SATA NCQ NON-DATA log
0x13       GPL     R/O      1  SATA NCQ Send and Receive log
0x15       GPL     R/W      1  SATA Rebuild Assist log
0x21       GPL     R/O      1  Write stream error log
0x22       GPL     R/O      1  Read stream error log
0x24       GPL     R/O    256  Current Device Internal Status Data log
0x25       GPL     R/O    256  Saved Device Internal Status Data log
0x30       GPL,SL  R/O      9  IDENTIFY DEVICE data log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (1 sectors)
No Errors Logged

SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  3
SCT Version (vendor specific):       256 (0x0100)
SCT Support Level:                   0
Device State:                        Active (0)
Current Temperature:                    40 Celsius
Power Cycle Min/Max Temperature:     36/40 Celsius
Lifetime    Min/Max Temperature:     18/51 Celsius
Under/Over Temperature Limit Count:   0/0

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:      0/65 Celsius
Min/Max Temperature Limit:           -40/70 Celsius
Temperature History Size (Index):    128 (34)

Index    Estimated Time   Temperature Celsius
  35    2019-04-16 17:32    37  ******************
 ...    ..(  5 skipped).    ..  ******************
  41    2019-04-16 17:38    37  ******************
  42    2019-04-16 17:39    38  *******************
 ...    ..( 54 skipped).    ..  *******************
  97    2019-04-16 18:34    38  *******************
  98    2019-04-16 18:35    39  ********************
 ...    ..( 53 skipped).    ..  ********************
  24    2019-04-16 19:29    39  ********************
  25    2019-04-16 19:30    40  *********************
 ...    ..(  7 skipped).    ..  *********************
  33    2019-04-16 19:38    40  *********************
  34    2019-04-16 19:39    37  ******************

SCT Error Recovery Control:
           Read:     70 (7.0 seconds)
          Write:     70 (7.0 seconds)

Device Statistics (GP/SMART Log 0x04) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  2            0  Command failed due to ICRC error
0x0002  2            0  R_ERR response for data FIS
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0005  2            0  R_ERR response for non-data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS
0x0008  2            0  Device-to-host non-data FIS retries
0x0009  2            0  Transition from drive PhyRdy to drive PhyNRdy
0x000a  2            1  Device-to-host register FISes sent due to a COMRESET
0x000b  2            0  CRC errors within host-to-device FIS
0x000d  2            0  Non-CRC errors within host-to-device FIS

/dev/ada2
smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.1-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Western Digital Red
Device Model:     WDC WD60EFRX-68L0BN1
Serial Number:    WD-WX31DB58Y6XX
LU WWN Device Id: 5 0014ee 20d3d10b7
Firmware Version: 82.00A82
User Capacity:    6,001,175,126,016 bytes [6.00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5700 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ACS-2, ACS-3 T13/2161-D revision 3b
SATA Version is:  SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Tue Apr 16 19:39:45 2019 PDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Unavailable
APM feature is:   Unavailable
Rd look-ahead is: Enabled
Write cache is:   Enabled
ATA Security is:  Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		( 7184) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 ( 725) minutes.
Conveyance self-test routine
recommended polling time: 	 (   5) minutes.
SCT capabilities: 	       (0x303d)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR-K   200   200   051    -    0
  3 Spin_Up_Time            POS--K   223   197   021    -    7841
  4 Start_Stop_Count        -O--CK   100   100   000    -    37
  5 Reallocated_Sector_Ct   PO--CK   200   200   140    -    0
  7 Seek_Error_Rate         -OSR-K   200   200   000    -    0
  9 Power_On_Hours          -O--CK   069   069   000    -    22989
 10 Spin_Retry_Count        -O--CK   100   253   000    -    0
 11 Calibration_Retry_Count -O--CK   100   253   000    -    0
 12 Power_Cycle_Count       -O--CK   100   100   000    -    37
192 Power-Off_Retract_Count -O--CK   200   200   000    -    19
193 Load_Cycle_Count        -O--CK   200   200   000    -    144
194 Temperature_Celsius     -O---K   113   099   000    -    39
196 Reallocated_Event_Count -O--CK   200   200   000    -    0
197 Current_Pending_Sector  -O--CK   200   200   000    -    0
198 Offline_Uncorrectable   ----CK   100   253   000    -    0
199 UDMA_CRC_Error_Count    -O--CK   200   200   000    -    0
200 Multi_Zone_Error_Rate   ---R--   200   200   000    -    0
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      5  Comprehensive SMART error log
0x03       GPL     R/O      6  Ext. Comprehensive SMART error log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      1  Extended self-test log
0x09           SL  R/W      1  Selective self-test log
0x10       GPL     R/O      1  SATA NCQ Queued Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x21       GPL     R/O      1  Write stream error log
0x22       GPL     R/O      1  Read stream error log
0x30       GPL,SL  R/O      9  IDENTIFY DEVICE data log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xa0-0xa7  GPL,SL  VS      16  Device vendor specific log
0xa8-0xb6  GPL,SL  VS       1  Device vendor specific log
0xb7       GPL,SL  VS      54  Device vendor specific log
0xbd       GPL,SL  VS       1  Device vendor specific log
0xc0       GPL,SL  VS       1  Device vendor specific log
0xc1       GPL     VS      93  Device vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 137 (device log contains only the most recent 24 errors)
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 137 [16] occurred at disk power-on lifetime: 22971 hours (957 days + 3 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 00 44 a4 30 40 00  Error: UNC at LBA = 0x0044a430 = 4498480

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 08 00 38 00 02 8f c7 03 48 40 08     00:12:00.103  READ FPDMA QUEUED
  60 00 08 00 30 00 02 b1 cb b2 88 40 08     00:12:00.103  READ FPDMA QUEUED
  60 00 08 00 28 00 01 28 4d 9b 50 40 08     00:12:00.103  READ FPDMA QUEUED
  60 00 08 00 20 00 00 00 44 a4 30 40 08     00:11:55.174  READ FPDMA QUEUED
  ea 00 00 00 00 00 00 00 00 00 00 40 08     00:11:54.874  FLUSH CACHE EXT

Error 136 [15] occurred at disk power-on lifetime: 22967 hours (956 days + 23 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  10 -- 51 00 00 00 01 29 a6 f7 90 40 00  Error: IDNF at LBA = 0x129a6f790 = 4993775504

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 00 08 00 10 00 01 29 a6 f7 90 40 08  7d+22:25:04.193  WRITE FPDMA QUEUED
  ea 00 00 00 00 00 00 00 00 00 00 40 08  7d+22:24:24.469  FLUSH CACHE EXT
  61 00 08 00 00 00 02 ba a0 f4 20 40 08  7d+22:24:24.468  WRITE FPDMA QUEUED
  61 00 08 00 f8 00 02 ba a0 f2 20 40 08  7d+22:24:24.468  WRITE FPDMA QUEUED
  61 00 08 00 f0 00 00 00 40 04 20 40 08  7d+22:24:24.467  WRITE FPDMA QUEUED

Error 135 [14] occurred at disk power-on lifetime: 22960 hours (956 days + 16 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 83 dc ff 10 40 00  Error: UNC at LBA = 0x83dcff10 = 2212298512

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 58 00 68 00 00 83 dc fe b8 40 08  7d+15:52:06.041  READ FPDMA QUEUED
  60 00 58 00 60 00 00 83 dc ff 10 40 08  7d+15:52:05.954  READ FPDMA QUEUED
  ea 00 00 00 00 00 00 00 00 00 00 40 08  7d+15:52:02.009  FLUSH CACHE EXT
  61 00 08 00 50 00 02 ba a0 f3 b8 40 08  7d+15:52:02.008  WRITE FPDMA QUEUED
  61 00 08 00 48 00 02 ba a0 f1 b8 40 08  7d+15:52:02.008  WRITE FPDMA QUEUED

Error 134 [13] occurred at disk power-on lifetime: 22960 hours (956 days + 16 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 83 e0 ba e8 40 00  Error: WP at LBA = 0x83e0bae8 = 2212543208

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 00 08 00 90 00 01 29 cc 6d c0 40 08  7d+15:51:56.796  WRITE FPDMA QUEUED
  60 00 28 00 88 00 00 83 e0 bb 40 40 08  7d+15:51:53.434  READ FPDMA QUEUED
  60 00 58 00 80 00 00 83 e0 ba e8 40 08  7d+15:51:53.434  READ FPDMA QUEUED
  ea 00 00 00 00 00 00 00 00 00 00 40 08  7d+15:51:51.899  FLUSH CACHE EXT
  61 00 08 00 70 00 02 ba a0 f3 a8 40 08  7d+15:51:51.898  WRITE FPDMA QUEUED

Error 133 [12] occurred at disk power-on lifetime: 22960 hours (956 days + 16 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 83 80 3a d0 40 00  Error: UNC at LBA = 0x83803ad0 = 2206218960

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 58 00 00 00 00 83 80 3b 80 40 08  7d+15:51:06.789  READ FPDMA QUEUED
  60 00 58 00 f8 00 00 83 80 3b 28 40 08  7d+15:51:05.656  READ FPDMA QUEUED
  60 00 58 00 f0 00 00 83 80 3a d0 40 08  7d+15:51:03.612  READ FPDMA QUEUED
  60 00 58 00 e8 00 00 83 80 38 68 40 08  7d+15:50:58.621  READ FPDMA QUEUED
  60 00 58 00 e0 00 00 83 80 38 10 40 08  7d+15:50:57.730  READ FPDMA QUEUED

Error 132 [11] occurred at disk power-on lifetime: 22960 hours (956 days + 16 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 83 7f f7 10 40 00  Error: UNC at LBA = 0x837ff710 = 2206201616

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 58 00 90 00 00 83 7f f7 c0 40 08  7d+15:48:05.452  READ FPDMA QUEUED
  60 00 58 00 88 00 00 83 7f f7 68 40 08  7d+15:48:04.578  READ FPDMA QUEUED
  60 00 58 00 80 00 00 83 7f f7 10 40 08  7d+15:48:03.763  READ FPDMA QUEUED
  60 00 58 00 78 00 00 83 7f f6 b8 40 08  7d+15:48:02.975  READ FPDMA QUEUED
  60 00 58 00 70 00 00 83 7f f4 50 40 08  7d+15:47:58.036  READ FPDMA QUEUED

Error 131 [10] occurred at disk power-on lifetime: 22956 hours (956 days + 12 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 02 ba a0 f0 90 40 00  Error: UNC at LBA = 0x2baa0f090 = 11721044112

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 10 00 38 00 02 ba a0 f2 90 40 08  7d+11:54:13.391  READ FPDMA QUEUED
  60 00 10 00 30 00 02 ba a0 f0 90 40 08  7d+11:54:13.391  READ FPDMA QUEUED
  60 00 10 00 28 00 00 00 40 02 90 40 08  7d+11:54:13.390  READ FPDMA QUEUED
  ea 00 00 00 00 00 00 00 00 00 00 40 08  7d+11:54:10.107  FLUSH CACHE EXT
  61 00 08 00 18 00 02 ba a0 f3 90 40 08  7d+11:54:10.107  WRITE FPDMA QUEUED

Error 130 [9] occurred at disk power-on lifetime: 22956 hours (956 days + 12 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 00 00 00 00 40 00  Error: WP at LBA = 0x00000000 = 0

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 00 08 00 58 00 01 29 cb 7c 88 40 08  7d+11:54:05.002  WRITE FPDMA QUEUED
  60 01 00 00 50 00 00 00 00 00 00 40 08  7d+11:54:00.884  READ FPDMA QUEUED
  ea 00 00 00 00 00 00 00 00 00 00 40 08  7d+11:53:50.178  FLUSH CACHE EXT
  61 00 08 00 40 00 02 ba a0 f4 70 40 08  7d+11:53:50.177  WRITE FPDMA QUEUED
  61 00 08 00 38 00 02 ba a0 f2 70 40 08  7d+11:53:50.177  WRITE FPDMA QUEUED

SMART Extended Self-test Log Version: 1 (1 sectors)
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%     22836         -
# 2  Extended offline    Completed without error       00%     22708         -
# 3  Short offline       Completed without error       00%     22669         -
# 4  Short offline       Completed without error       00%     22601         -
# 5  Short offline       Completed without error       00%     22433         -
# 6  Short offline       Completed without error       00%     22235         -
# 7  Extended offline    Completed without error       00%     22106         -
# 8  Short offline       Completed without error       00%     22067         -
# 9  Short offline       Completed without error       00%     21899         -
#10  Short offline       Completed without error       00%     21756         -
#11  Short offline       Completed without error       00%     21588         -
#12  Extended offline    Completed without error       00%     21459         -
#13  Short offline       Completed without error       00%     21420         -
#14  Short offline       Completed without error       00%     21348         -
#15  Short offline       Completed without error       00%     21181         -
#16  Short offline       Completed without error       00%     21013         -
#17  Short offline       Completed without error       00%     20845         -
#18  Extended offline    Completed without error       00%     20716         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  3
SCT Version (vendor specific):       258 (0x0102)
SCT Support Level:                   1
Device State:                        Active (0)
Current Temperature:                    39 Celsius
Power Cycle Min/Max Temperature:     35/39 Celsius
Lifetime    Min/Max Temperature:     16/53 Celsius
Under/Over Temperature Limit Count:   0/0
Vendor specific:
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:      0/60 Celsius
Min/Max Temperature Limit:           -41/85 Celsius
Temperature History Size (Index):    478 (228)

Index    Estimated Time   Temperature Celsius
 229    2019-04-16 11:42    37  ******************
 ...    ..( 10 skipped).    ..  ******************
 240    2019-04-16 11:53    37  ******************
 241    2019-04-16 11:54    38  *******************
 ...    ..( 70 skipped).    ..  *******************
 312    2019-04-16 13:05    38  *******************
 313    2019-04-16 13:06    39  ********************
 ...    ..(  8 skipped).    ..  ********************
 322    2019-04-16 13:15    39  ********************
 323    2019-04-16 13:16    36  *****************
 ...    ..(  7 skipped).    ..  *****************
 331    2019-04-16 13:24    36  *****************
 332    2019-04-16 13:25    35  ****************
 ...    ..(280 skipped).    ..  ****************
 135    2019-04-16 18:06    35  ****************
 136    2019-04-16 18:07    36  *****************
 ...    ..( 56 skipped).    ..  *****************
 193    2019-04-16 19:04    36  *****************
 194    2019-04-16 19:05    37  ******************
 ...    ..( 33 skipped).    ..  ******************
 228    2019-04-16 19:39    37  ******************

SCT Error Recovery Control:
           Read:     70 (7.0 seconds)
          Write:     70 (7.0 seconds)

Device Statistics (GP/SMART Log 0x04) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  2            0  Command failed due to ICRC error
0x0002  2            0  R_ERR response for data FIS
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0005  2            0  R_ERR response for non-data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS
0x0008  2            0  Device-to-host non-data FIS retries
0x0009  2            8  Transition from drive PhyRdy to drive PhyNRdy
0x000a  2           10  Device-to-host register FISes sent due to a COMRESET
0x000b  2            0  CRC errors within host-to-device FIS
0x000d  2            0  Non-CRC errors within host-to-device FIS
0x000f  2            0  R_ERR response for host-to-device data FIS, CRC
0x0012  2            0  R_ERR response for host-to-device non-data FIS, CRC
0x8000  4        68000  Vendor specific

/dev/ada1
smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.1-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Western Digital Red
Device Model:     WDC WD60EFRX-68L0BN1
Serial Number:    WD-WXB1HB4X697T
LU WWN Device Id: 5 0014ee 2b7a5366c
Firmware Version: 82.00A82
User Capacity:    6,001,175,126,016 bytes [6.00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5700 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ACS-2, ACS-3 T13/2161-D revision 3b
SATA Version is:  SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Tue Apr 16 19:39:46 2019 PDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Unavailable
APM feature is:   Unavailable
Rd look-ahead is: Enabled
Write cache is:   Enabled
ATA Security is:  Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		( 6524) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 ( 719) minutes.
Conveyance self-test routine
recommended polling time: 	 (   5) minutes.
SCT capabilities: 	       (0x303d)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR-K   200   200   051    -    0
  3 Spin_Up_Time            POS--K   198   196   021    -    9058
  4 Start_Stop_Count        -O--CK   100   100   000    -    59
  5 Reallocated_Sector_Ct   PO--CK   200   200   140    -    0
  7 Seek_Error_Rate         -OSR-K   100   253   000    -    0
  9 Power_On_Hours          -O--CK   069   069   000    -    23067
 10 Spin_Retry_Count        -O--CK   100   253   000    -    0
 11 Calibration_Retry_Count -O--CK   100   253   000    -    0
 12 Power_Cycle_Count       -O--CK   100   100   000    -    59
192 Power-Off_Retract_Count -O--CK   200   200   000    -    38
193 Load_Cycle_Count        -O--CK   200   200   000    -    203
194 Temperature_Celsius     -O---K   112   095   000    -    40
196 Reallocated_Event_Count -O--CK   200   200   000    -    0
197 Current_Pending_Sector  -O--CK   200   200   000    -    0
198 Offline_Uncorrectable   ----CK   100   253   000    -    0
199 UDMA_CRC_Error_Count    -O--CK   200   200   000    -    0
200 Multi_Zone_Error_Rate   ---R--   200   200   000    -    0
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      5  Comprehensive SMART error log
0x03       GPL     R/O      6  Ext. Comprehensive SMART error log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      1  Extended self-test log
0x09           SL  R/W      1  Selective self-test log
0x10       GPL     R/O      1  SATA NCQ Queued Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x21       GPL     R/O      1  Write stream error log
0x22       GPL     R/O      1  Read stream error log
0x30       GPL,SL  R/O      9  IDENTIFY DEVICE data log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xa0-0xa7  GPL,SL  VS      16  Device vendor specific log
0xa8-0xb6  GPL,SL  VS       1  Device vendor specific log
0xb7       GPL,SL  VS      40  Device vendor specific log
0xbd       GPL,SL  VS       1  Device vendor specific log
0xc0       GPL,SL  VS       1  Device vendor specific log
0xc1       GPL     VS      93  Device vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
No Errors Logged

SMART Extended Self-test Log Version: 1 (1 sectors)
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%     23028         -
# 2  Short offline       Completed without error       00%     22860         -
# 3  Extended offline    Completed without error       00%     22731         -
# 4  Short offline       Completed without error       00%     22693         -
# 5  Short offline       Completed without error       00%     22625         -
# 6  Short offline       Completed without error       00%     22457         -
# 7  Short offline       Completed without error       00%     22259         -
# 8  Extended offline    Completed without error       00%     22130         -
# 9  Short offline       Completed without error       00%     22091         -
#10  Short offline       Completed without error       00%     21923         -
#11  Short offline       Completed without error       00%     21780         -
#12  Short offline       Completed without error       00%     21612         -
#13  Extended offline    Completed without error       00%     21483         -
#14  Short offline       Completed without error       00%     21444         -
#15  Short offline       Completed without error       00%     21372         -
#16  Short offline       Completed without error       00%     21204         -
#17  Short offline       Completed without error       00%     21036         -
#18  Short offline       Completed without error       00%     20869         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  3
SCT Version (vendor specific):       258 (0x0102)
SCT Support Level:                   1
Device State:                        Active (0)
Current Temperature:                    40 Celsius
Power Cycle Min/Max Temperature:     37/42 Celsius
Lifetime    Min/Max Temperature:      2/57 Celsius
Under/Over Temperature Limit Count:   0/0
Vendor specific:
00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:      0/60 Celsius
Min/Max Temperature Limit:           -41/85 Celsius
Temperature History Size (Index):    478 (202)

Index    Estimated Time   Temperature Celsius
 203    2019-04-16 11:42    39  ********************
 ...    ..( 19 skipped).    ..  ********************
 223    2019-04-16 12:02    39  ********************
 224    2019-04-16 12:03    40  *********************
 ...    ..( 71 skipped).    ..  *********************
 296    2019-04-16 13:15    40  *********************
 297    2019-04-16 13:16    38  *******************
 ...    ..( 72 skipped).    ..  *******************
 370    2019-04-16 14:29    38  *******************
 371    2019-04-16 14:30    37  ******************
 ...    ..(213 skipped).    ..  ******************
 107    2019-04-16 18:04    37  ******************
 108    2019-04-16 18:05    38  *******************
 ...    ..( 54 skipped).    ..  *******************
 163    2019-04-16 19:00    38  *******************
 164    2019-04-16 19:01    39  ********************
 ...    ..( 37 skipped).    ..  ********************
 202    2019-04-16 19:39    39  ********************

SCT Error Recovery Control:
           Read:     70 (7.0 seconds)
          Write:     70 (7.0 seconds)

Device Statistics (GP/SMART Log 0x04) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  2            0  Command failed due to ICRC error
0x0002  2            0  R_ERR response for data FIS
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0005  2            0  R_ERR response for non-data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS
0x0008  2            0  Device-to-host non-data FIS retries
0x0009  2            8  Transition from drive PhyRdy to drive PhyNRdy
0x000a  2           10  Device-to-host register FISes sent due to a COMRESET
0x000b  2            0  CRC errors within host-to-device FIS
0x000f  2            0  R_ERR response for host-to-device data FIS, CRC
0x0012  2            0  R_ERR response for host-to-device non-data FIS, CRC
0x8000  4        68000  Vendor specific

/dev/ada0
smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.1-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Western Digital Red
Device Model:     WDC WD60EFRX-68L0BN1
Serial Number:    WD-WXB1HB4Z9PYH
LU WWN Device Id: 5 0014ee 20d3cffa1
Firmware Version: 82.00A82
User Capacity:    6,001,175,126,016 bytes [6.00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5700 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ACS-2, ACS-3 T13/2161-D revision 3b
SATA Version is:  SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Tue Apr 16 19:39:46 2019 PDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Unavailable
APM feature is:   Unavailable
Rd look-ahead is: Enabled
Write cache is:   Enabled
ATA Security is:  Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		( 6164) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 ( 715) minutes.
Conveyance self-test routine
recommended polling time: 	 (   5) minutes.
SCT capabilities: 	       (0x303d)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR-K   200   200   051    -    0
  3 Spin_Up_Time            POS--K   197   197   021    -    9108
  4 Start_Stop_Count        -O--CK   100   100   000    -    38
  5 Reallocated_Sector_Ct   PO--CK   200   200   140    -    0
  7 Seek_Error_Rate         -OSR-K   200   200   000    -    0
  9 Power_On_Hours          -O--CK   069   069   000    -    23043
 10 Spin_Retry_Count        -O--CK   100   253   000    -    0
 11 Calibration_Retry_Count -O--CK   100   253   000    -    0
 12 Power_Cycle_Count       -O--CK   100   100   000    -    38
192 Power-Off_Retract_Count -O--CK   200   200   000    -    17
193 Load_Cycle_Count        -O--CK   200   200   000    -    144
194 Temperature_Celsius     -O---K   110   092   000    -    42
196 Reallocated_Event_Count -O--CK   200   200   000    -    0
197 Current_Pending_Sector  -O--CK   200   200   000    -    0
198 Offline_Uncorrectable   ----CK   100   253   000    -    0
199 UDMA_CRC_Error_Count    -O--CK   200   200   000    -    0
200 Multi_Zone_Error_Rate   ---R--   200   200   000    -    0
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      5  Comprehensive SMART error log
0x03       GPL     R/O      6  Ext. Comprehensive SMART error log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      1  Extended self-test log
0x09           SL  R/W      1  Selective self-test log
0x10       GPL     R/O      1  SATA NCQ Queued Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x21       GPL     R/O      1  Write stream error log
0x22       GPL     R/O      1  Read stream error log
0x30       GPL,SL  R/O      9  IDENTIFY DEVICE data log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xa0-0xa7  GPL,SL  VS      16  Device vendor specific log
0xa8-0xb6  GPL,SL  VS       1  Device vendor specific log
0xb7       GPL,SL  VS      54  Device vendor specific log
0xbd       GPL,SL  VS       1  Device vendor specific log
0xc0       GPL,SL  VS       1  Device vendor specific log
0xc1       GPL     VS      93  Device vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 4
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 4 [3] occurred at disk power-on lifetime: 11597 hours (483 days + 5 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 01 e8 22 27 58 40 00  Error: UNC at LBA = 0x1e8222758 = 8189519704

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 b0 00 78 00 01 e8 22 28 08 40 08  3d+18:16:45.298  READ FPDMA QUEUED
  60 00 b0 00 70 00 01 e8 22 27 58 40 08  3d+18:16:45.297  READ FPDMA QUEUED
  60 00 b0 00 68 00 01 e8 22 26 a8 40 08  3d+18:16:45.296  READ FPDMA QUEUED
  60 00 b0 00 60 00 01 e8 22 25 f8 40 08  3d+18:16:45.285  READ FPDMA QUEUED
  60 00 b0 00 58 00 01 e8 22 25 48 40 08  3d+18:16:45.285  READ FPDMA QUEUED

Error 3 [2] occurred at disk power-on lifetime: 11595 hours (483 days + 3 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 02 75 2e 2f d0 40 00  Error: UNC at LBA = 0x2752e2fd0 = 10555895760

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 58 00 98 00 02 75 2e 30 80 40 08  3d+16:18:33.108  READ FPDMA QUEUED
  60 00 b0 00 90 00 02 75 2e 2f d0 40 08  3d+16:18:33.108  READ FPDMA QUEUED
  60 00 b0 00 88 00 02 75 2e 2f 20 40 08  3d+16:18:33.106  READ FPDMA QUEUED
  60 00 b0 00 80 00 02 75 2e 2e 70 40 08  3d+16:18:33.106  READ FPDMA QUEUED
  60 00 b0 00 78 00 02 75 2e 2d c0 40 08  3d+16:18:33.104  READ FPDMA QUEUED

Error 2 [1] occurred at disk power-on lifetime: 11593 hours (483 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 02 8d 5b 00 c0 40 00  Error: UNC at LBA = 0x28d5b00c0 = 10961486016

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 b0 00 98 00 02 8d 5b 01 70 40 08  3d+13:38:42.181  READ FPDMA QUEUED
  60 00 b0 00 90 00 02 8d 5b 00 c0 40 08  3d+13:38:42.181  READ FPDMA QUEUED
  60 00 b0 00 88 00 02 8d 5b 00 10 40 08  3d+13:38:42.179  READ FPDMA QUEUED
  60 00 b0 00 80 00 02 8d 5a ff 60 40 08  3d+13:38:42.168  READ FPDMA QUEUED
  60 00 b0 00 78 00 02 8d 5a fe b0 40 08  3d+13:38:42.168  READ FPDMA QUEUED

Error 1 [0] occurred at disk power-on lifetime: 8771 hours (365 days + 11 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 02 8d 5b 00 c0 40 00  Error: UNC at LBA = 0x28d5b00c0 = 10961486016

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 b0 00 e0 00 02 8d 5b 01 70 40 08 27d+12:41:23.855  READ FPDMA QUEUED
  60 00 b0 00 d8 00 02 8d 5b 00 c0 40 08 27d+12:41:23.855  READ FPDMA QUEUED
  60 00 b0 00 d0 00 02 8d 5b 00 10 40 08 27d+12:41:23.853  READ FPDMA QUEUED
  60 00 b0 00 c8 00 02 8d 5a ff 60 40 08 27d+12:41:23.842  READ FPDMA QUEUED
  60 00 b0 00 c0 00 02 8d 5a fe b0 40 08 27d+12:41:23.842  READ FPDMA QUEUED

SMART Extended Self-test Log Version: 1 (1 sectors)
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%     23004         -
# 2  Short offline       Completed without error       00%     22836         -
# 3  Extended offline    Completed without error       00%     22708         -
# 4  Short offline       Completed without error       00%     22669         -
# 5  Short offline       Completed without error       00%     22601         -
# 6  Short offline       Completed without error       00%     22433         -
# 7  Short offline       Completed without error       00%     22235         -
# 8  Extended offline    Completed without error       00%     22106         -
# 9  Short offline       Completed without error       00%     22067         -
#10  Short offline       Completed without error       00%     21900         -
#11  Short offline       Completed without error       00%     21756         -
#12  Short offline       Completed without error       00%     21588         -
#13  Extended offline    Completed without error       00%     21459         -
#14  Short offline       Completed without error       00%     21420         -
#15  Short offline       Completed without error       00%     21348         -
#16  Short offline       Completed without error       00%     21181         -
#17  Short offline       Completed without error       00%     21013         -
#18  Short offline       Completed without error       00%     20845         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  3
SCT Version (vendor specific):       258 (0x0102)
SCT Support Level:                   1
Device State:                        Active (0)
Current Temperature:                    42 Celsius
Power Cycle Min/Max Temperature:     39/43 Celsius
Lifetime    Min/Max Temperature:     15/60 Celsius
Under/Over Temperature Limit Count:   0/0
Vendor specific:
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:      0/60 Celsius
Min/Max Temperature Limit:           -41/85 Celsius
Temperature History Size (Index):    478 (173)

Index    Estimated Time   Temperature Celsius
 174    2019-04-16 11:42    41  **********************
 ...    ..( 39 skipped).    ..  **********************
 214    2019-04-16 12:22    41  **********************
 215    2019-04-16 12:23    42  ***********************
 ...    ..( 51 skipped).    ..  ***********************
 267    2019-04-16 13:15    42  ***********************
 268    2019-04-16 13:16    39  ********************
 ...    ..(308 skipped).    ..  ********************
  99    2019-04-16 18:25    39  ********************
 100    2019-04-16 18:26    40  *********************
 ...    ..( 44 skipped).    ..  *********************
 145    2019-04-16 19:11    40  *********************
 146    2019-04-16 19:12    41  **********************
 ...    ..( 26 skipped).    ..  **********************
 173    2019-04-16 19:39    41  **********************

SCT Error Recovery Control:
           Read:     70 (7.0 seconds)
          Write:     70 (7.0 seconds)

Device Statistics (GP/SMART Log 0x04) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  2            0  Command failed due to ICRC error
0x0002  2            0  R_ERR response for data FIS
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0005  2            0  R_ERR response for non-data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS
0x0008  2            0  Device-to-host non-data FIS retries
0x0009  2            8  Transition from drive PhyRdy to drive PhyNRdy
0x000a  2           10  Device-to-host register FISes sent due to a COMRESET
0x000b  2            0  CRC errors within host-to-device FIS
0x000d  2            0  Non-CRC errors within host-to-device FIS
0x000f  2            0  R_ERR response for host-to-device data FIS, CRC
0x0012  2            0  R_ERR response for host-to-device non-data FIS, CRC
0x8000  4        68000  Vendor specific

/dev/da0
smartctl 6.5 2016-05-07 r4318 [FreeBSD 11.1-STABLE amd64] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

/dev/da0: Unknown USB bridge [0x0781:0x5590 (0x100)]
Please specify device type with the -d option.

Use smartctl -h to get a usage summary

debug finished in 2 seconds for SMART - 'smartctl -x'
command used:
/usr/local/www/smart.sh


