smartctl 7.2 2020-12-30 r5155 [FreeBSD 12.2-RELEASE-p12 amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Red Device Model: WDC WD80EFAX-68LHPN0 Serial Number: 7SGM2G3C LU WWN Device Id: 5 000cca 252c8ac44 Firmware Version: 83.H0A83 User Capacity: 8,001,563,222,016 bytes [8.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Apr 12 09:36:52 2022 CDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 93) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 958) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0 2 Throughput_Performance 0x0004 129 129 054 Old_age Offline - 113 3 Spin_Up_Time 0x0007 153 153 024 Pre-fail Always - 447 (Average 410) 4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 198 5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0 7 Seek_Error_Rate 0x000a 100 100 067 Old_age Always - 0 8 Seek_Time_Performance 0x0004 128 128 020 Old_age Offline - 18 9 Power_On_Hours 0x0012 095 095 000 Old_age Always - 36232 10 Spin_Retry_Count 0x0012 100 100 060 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 189 22 Helium_Level 0x0023 100 100 025 Pre-fail Always - 100 192 Power-Off_Retract_Count 0x0032 099 099 000 Old_age Always - 1605 193 Load_Cycle_Count 0x0012 099 099 000 Old_age Always - 1605 194 Temperature_Celsius 0x0002 224 224 000 Old_age Always - 29 (Min/Max 18/45) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 67 SMART Error Log Version: 1 ATA Error Count: 67 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 67 occurred at disk power-on lifetime: 36202 hours (1508 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 00 80 03 40 40 00 1d+22:24:16.078 READ FPDMA QUEUED 2f 00 01 10 00 00 00 00 1d+22:24:16.070 READ LOG EXT 2f 00 01 10 00 00 00 00 1d+22:24:16.070 READ LOG EXT 60 00 00 80 03 40 40 00 1d+22:24:16.062 READ FPDMA QUEUED ec 00 00 00 00 00 00 00 1d+22:24:16.062 IDENTIFY DEVICE Error 66 occurred at disk power-on lifetime: 36202 hours (1508 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 00 80 03 40 40 00 1d+22:24:16.070 READ FPDMA QUEUED ec 00 00 00 00 00 00 00 1d+22:24:16.062 IDENTIFY DEVICE 2f 00 01 10 00 00 00 00 1d+22:24:16.061 READ LOG EXT 2f 00 01 10 00 00 00 00 1d+22:24:16.061 READ LOG EXT 60 00 00 80 03 40 40 00 1d+22:24:16.043 READ FPDMA QUEUED Error 65 occurred at disk power-on lifetime: 36202 hours (1508 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 00 80 03 40 40 00 1d+22:24:16.061 READ FPDMA QUEUED ef 10 02 00 00 00 00 00 1d+22:24:15.990 SET FEATURES [Enable SATA feature] ef 02 00 00 00 00 00 00 1d+22:24:15.987 SET FEATURES [Enable write cache] ef aa 00 00 00 00 00 00 1d+22:24:15.983 SET FEATURES [Enable read look-ahead] ef 03 46 00 00 00 00 00 1d+22:24:15.980 SET FEATURES [Set transfer mode] Error 64 occurred at disk power-on lifetime: 36202 hours (1508 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 00 80 03 40 40 00 1d+22:24:14.811 READ FPDMA QUEUED ef 10 02 00 00 00 00 00 1d+22:24:14.724 SET FEATURES [Enable SATA feature] ef 02 00 00 00 00 00 00 1d+22:24:14.720 SET FEATURES [Enable write cache] ef aa 00 00 00 00 00 00 1d+22:24:14.717 SET FEATURES [Enable read look-ahead] ef 03 46 00 00 00 00 00 1d+22:24:14.714 SET FEATURES [Set transfer mode] Error 63 occurred at disk power-on lifetime: 36202 hours (1508 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 41 00 00 00 00 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 00 80 03 40 40 00 1d+22:24:13.561 READ FPDMA QUEUED ef 10 02 00 00 00 00 00 1d+22:24:13.490 SET FEATURES [Enable SATA feature] ef 02 00 00 00 00 00 00 1d+22:24:13.486 SET FEATURES [Enable write cache] ef aa 00 00 00 00 00 00 1d+22:24:13.483 SET FEATURES [Enable read look-ahead] ef 03 46 00 00 00 00 00 1d+22:24:13.480 SET FEATURES [Set transfer mode] SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 36184 - # 2 Short offline Completed without error 00% 36017 - # 3 Extended offline Completed without error 00% 36001 - # 4 Short offline Completed without error 00% 35849 - # 5 Short offline Completed without error 00% 35681 - # 6 Short offline Completed without error 00% 35514 - # 7 Short offline Completed without error 00% 35348 - # 8 Extended offline Completed without error 00% 35251 - # 9 Short offline Completed without error 00% 35179 - #10 Short offline Completed without error 00% 35026 - #11 Short offline Completed without error 00% 34858 - #12 Short offline Completed without error 00% 34690 - #13 Extended offline Completed without error 00% 34593 - #14 Short offline Completed without error 00% 34521 - #15 Short offline Completed without error 00% 34353 - #16 Short offline Completed without error 00% 34185 - #17 Short offline Completed without error 00% 34018 - #18 Short offline Completed without error 00% 33849 - #19 Extended offline Completed without error 00% 33846 - #20 Short offline Completed without error 00% 33683 - #21 Short offline Completed without error 00% 33542 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.